بایگانی برچسب: damage

In this tutorial, the Simulation dynamic four points bending of the timber wood beam reinforced with CFRP rod and Gluein Abaqus has been investigated. The wood beam is modeled as a three-dimensional solid part with two compression and tension sections. The adhesive and CFRP rod also is modeled as three-dimensional ...

In this tutorial, the Simulation sequential CEL explosion in the depth of soil over the RC slab in Abaqus has been investigated. The concrete slab is modeled as three-dimensional solid part, the steel reinforcement is modeled as wire part. The Soil, and TNT are modeled as three-dimensional solid parts. The ...

In this tutorial, the Simulation UHPFRC beam with initial void reinforced with CFRP rod and Expoxy under dynamic bending has been investigated. The concrete beam, CFRP rod, epoxy glu are modeled as three-dimensional solid parts. Two rigid body as a hydraulic jacks also are modeled. You can see a figure ...

In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...

In this tutorial the Simulation CEL explosion inside the CFRP composite vessel in Abaqus has been investigated. The CFRP vessel is modeled as a three-dimensional shell part in sixteen layers with different oreintation. The TNT part is modeled as a three-dimensional solid part. The surounding is modeled as an Eurlerian ...

In this tutorial the Simulation low energy impact on the concrete slab with pre tensioned bars reinforced with GFRP in Abaqus has been studeid. Concrete is modeled as a three-dimensional solid part. The GFRP part is model as plannar shell part. The steel basrs are modeled as three-dimensional wire part ...

In this tutorial the Simulation CFRP water storage tank under close air blast explosion in Abaqus has been investigaed. The CFRP tank is modeled as a three-dimensional shell part. The water is modeled as solid part and it’ll used as reference volume in load section to define the amount and ...

This tutorial investigates a Simulation air blast explosion test over a reinforced UHPC- Damage analysis. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part. The embedded bars and strips parts are modeled as a three-dimensional wire part. You can see a figure of the assembled parts below The UHPC ...

In this tutorial, the Simulation of steel projectile impact to the Reinforced-Ultra-High-Performance Concrete- Damage investigation has been investigated. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part, the embedded beam parts are modeled as a three-dimensional wire part, and finally, the steel projectile is modeled as a solid part. ...

In this package, the high and low-velocity impacts are investigated through 40 step-by-step tutorials for more than 20 hours. Through those 40 separated simulations, all aspects of the impact and collision are studied. Each tutorial contains cae, inp, step-by-step English video, and papers, also some of them have codes. Impact ...

In this tutorial, the Simulation steel bullet impact to the armor panel(Ceramic- Aluminum Foam) in Abaqus has been investigated. The steel bullet is modeled as a three-dimensional solid part. The ceramic and aluminum foam are modeled as three-dimensional solid parts. Because of the symmetry conditions, one-quarter of the whole model ...

در این ویدئوی آموزشی به شبیه سازی برخورد گلوله فولادی به پنل مرکب سرامیک-فوم آلمینیوم در نرم افزار آباکوس پرداخته ایم. هدف از این شبیه سازی بررسی تخریب هدف و گلوله در اثر سرعت بالای برخورد می باشد. گلوله فولادی به صورت سه بعدی و تغییر شکلپذیر، لایه رویی سرامیکی ...

In this tutorial, the Simulation rigid projectile impact to the ceramic-CFRP panel in Abaqus-Damage investigation – has been done. The rigid projectile is modeled as a three-dimensional shell part. The ceramic is modeled as a three-dimensional thick solid part. The CFRP or carbon fiber is modeled as a three-dimensional shell ...

در این ویدئوی آموزشی به شبیه سازی برخورد صلب به یک پنل مرکب سرامیک-CFRP و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل پارت پرتابه صلب به صورت سه بعدی و شل، پارت هدف سرامیکی به صورت یک لایه ضخیم سه بعدی و سالید و در نهایت پارت ...

In this tutorial, the Simulation SPH explosion over the composite panel( Aluminum- Metal Foam) in Abaqus-Damage investigation – has been done. The explosive part, or the TNT is modeled as a three-dimensional solid part. The aluminum sheets are modeled as three-dimensional solid parts. The Aluminum Foam as a core is ...

In this tutorial, the Simulation rigid impact to the composite panel(CFRP+TPU+AL) in Abaqus-Damage investigation – has been studied. The CFRP part is modeled as a shell part with eight layers. The Thermoplastic polyurethane is modeled as a three-dimensional solid part. The Aluminum part is modeled as a three-dimensional solid part. ...

In this tutorial, the Simulation RC beam under the repeated impact of the rigid hammer in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The steel rebar and strips are modeled as three-dimensional wire parts. The rigid hammer is modeled as a three-dimensional rigid ...

In this tutorial, the Simulation Blast response of aluminum/thermoplastic polyurethane sandwich panels in Abaqus has been investigated. The aluminum sheets are modeled as three-dimensional solid parts. The TPU is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below. History presents evidence of the ...

In this tutorial, the Numerical analysis of tilted angle shear connectors in steel-concrete composite systems in Abaqus has been investigated. The concrete block is modeled as a three-dimensional solid part. The steel beam and steel angle connector are modeled as three-dimensional solid parts. Two rigid bodies are used as boundary ...

In this tutorial, the Simulation compression test of the concrete column with and without steel reinforcement-Compression test- has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts and two rigid bodies as boundary zone and hydraulic jack. You can ...

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

In this tutorial, the damage and failure investigation of the CFRP composite military helmet under close blast explosion has been studied. The military helmet is a 3D shell part with eight different layers. The helmet part is imported to the Abaqus because of the part complexity. You can see a ...

In this tutorial, the High-velocity impact of a bullet on the RC panel- Paper validation- is investigated. The dimensions are extracted from the paper. The concrete slab is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. The bullet is modeled as a discrete ...

In this tutorial, the Simulation cyclic loading of a composite Column(UHPC + Steel box) in Abaqus has been studied. The Ultra-High-Performance Concrete column is modeled as a three-dimensional solid part. The steel box cover is modeled as a three-dimensional shell part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation oblique high-velocity impact of an aluminum rod to the silicon-carbide target in Abaqus has been investigated. The silicon-carbide target is modeled as a three-dimensional solid part. The aluminum projectile is modeled as a three-dimensional solid part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation of low energy impact on the RC beam and residual displacement investigation in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire parts. The hammer is modeled as a rigid ...

In this tutorial, the Simulation of rigid body impact on the interior voided RC slab in Abaqus has been investigated. The RC voided slab is modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire parts. The rigid impactor is modeled as a three-dimensional shell part. ...

In this tutorial, the Simulation dynamic bending of RC beams strengthened with CFRP rods and Epoxy glue in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The CFRP rod and epoxy glue are modeled as three-dimensional solid parts. The steel bars and strips are ...

In this tutorial, the Simulation blast explosion over the composite panel(Steel-Aluminum-Ceramic-CFRP) in Abaqus has been investigated. The steel and aluminum plates are modeled as three-dimensional solid part. The silicon carbide or ceramic is modeled as a three-dimensional solid part. The CFRP is modeled as a three-dimensional solid part with four ...

In this tutorial, the Simulation dynamic bending test of an interior voided RC UHPC beam in Abaqus has been studied. The Ultra-High-Performance Concrete beam is modeled as three-dimensional solid part with interior sphere voids. The steel bar and strips are modeled as three-dimensional wire parts. The rigid bodies are used ...

In this tutorial, the Simulation ship moving through Ice-Water path in Abaqus by using SPH method has been done. The ship is imported to the Abaqus because of its complex geometry. The ice and water are modeled as a three-dimensional solid part. You can see a figure of the assembled ...

In this tutorial, the Simulation air blast load over a composite beam( UHPFRC- Steel beam with Shear stud) in Abaqus has been investigated. The Ultra-High-Performance-Fiber-Reinforced Concrete is modeled as a three-dimensional solid part. The stud is modeled as a three-dimensional solid part. The steel beam is modeled as a three-dimensional ...

In this tutorial, the Simulation air blast explosion over campsite slab(UHPC-Steel) by using cohesive interaction in Abaqus  has been done. The two steel covers are modeled as three-dimensional solid part. The Ultra-High-Performance concrete is modeled as a three-dimensional solid par. You can see a figure of the assembled parts below ...

In this tutorial, the Simulation low velocity impact on the CFRP-AL Foam-CFRP panel in Abaqus has been investigated. The CFRP are modeled as three-dimensional solid parts with four different fiber direction. The Aluminum-Foam as a core part is modeled as a three-dimensional solid part. The projectile is modeled as the ...

In this tutorial, the Simulation bending test of a steel-concrete(foamed concrete) composite beam in Abaqus  has been studied. The foamed concrete ( containing partial cement replacement) is modeled as a three-dimensional solid part. The steel beam is modeled as a three-dimensional shell part. The steel reinforcement is modeled as a ...

In this tutorial, the Simulation air blast explosion over a Wood-Concrete slab reinforced with BFRP lamina in Abaqus  has been investigated. The wood-concrete part is modeled as a three-dimensional solid part. The Basalt Fiber Reinforced Plastic( BFRP) is model as a shell part with eight layers. The steel reinforcement which ...

In this tutorial, the Simulation bending test of the UHPFRC beam reinforced with BFRP lamina in Abaqus  has been investigated. The UHPFRC beam is modeled as a three-dimensional solid part. The BFRP lamina with eight layers is modeled as a shell part. The steel bars and strips are modeled as ...

In this tutorial, the Simulation air blast explosion over the RC beam reinforce with Banana-Epoxy lamina in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The bar and strip are modeled as three-dimensional wire part. The Banana-Epoxy part is modeled as a three-dimensional shell ...

In this tutorial, the Simulation compression test of the short concrete column reinforce with Banana-Epoxy lamina in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The Banana-Epoxy lamina is modeled as a three-dimensional shell part. The steel bars and strips are modeled as three-dimensional ...

In this tutorial, the Simulation high-velocity impact of the steel rod to the composite panel(Steel-Ceramic-AFRP) in Abaqus  has been done. The steel rod and steel cover are modeled as three-dimensional solid part. The ceramic part is modeled as a three-dimensional solid part. The Aramid Fiber Reinforced Plastic(AFRP) is modeled as ...

In this tutorial, the Simulation four-point bending of a concrete beam reinforced with steel bar and BFRP in Abaqus  has been done. The concrete beam is modeled as a three-dimensional solid part. The Basalt Fiber reinforced Plastic(BFRP) is modeled as a shell part with four layers. The strips and bars ...

In this tutorial, the Simulation air blast explosion over the UHPC slab reinforced with BFRP composite in Abaqus has been investigated. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The Basalt fiber reinforced plastic(BFRP) is modeled as a shell part with four layers. You can see a figure of ...

In this tutorial, the Simulation retrofit Jute-Epoxy composite of the concrete column under dynamic compression in Abaqus  has been investigated. The concrete column is modeled as a three-dimensional solid part. The just-Epoxy part is modeled as a three-dimensional shell. A rigid body is used as the hydraulic jack. You can ...

In this tutorial, the Simulation three-point bending test of the UHPC beam reinforced with Jute-Epoxy lamina in Abaqus has been investigated. The UHPC beam is modeled as a three-dimensional solid part. The Jute-Epoxy lamina is modeled as a three-dimensional shell part with four layers. A rigid body shell part is ...

In this tutorial, the Simulation curved steel–UHPC–steel double skin composite panel under bending load in Abaqus has been investigated. The UHPC panel is modeled as a three-dimensional solid part. The steel skins are modeled as three-dimensional shell parts. You can see a figure of the assembled parts below Steel–UHPC–steel double ...

In this tutorial, the Simulation high velocity impact of the steel bullet on the Ceramic-Epoxy panel in Abaqus  has been investigated. The 3 alumina layers are modeled as three-dimensional solid part. The 2 epoxy glue layers are modeled as three-dimensional solid part. The steel bullet is modeled as a three-dimensional ...

In this tutorial, the Simulation dynamic bending test of a composite panel( UHPC-NSC) in Abaqus has been investigated. The Ultra-High-Performance Concrete and Normal Strength Concrete are modeled as three-dimensional solid parts. The steel bars are modeled as three-dimensional wire part. A shell rigid body is used as a hydraulic jack ...

In this tutorial, the Simulation CEL explosion in the depth of soil near a solid steel pipe in Abaqus  has been done. The Eulerian domain is modeled as a three-dimensional Eulerial part. The air, soil, and TNT are modeled as three-dimensional solid part. The steel pipe is model as a ...

In this tutorial, the Simulation air blast explosion over the composite RC slab( UHPC and NSC) in Abaqus has been investigated. the Ultra High Performance Concrete(UHPC) and Normal Strength Concrete(NSC) are modeled as three-dimensional solid part. The UHPC is the upper face and the NSC is the bottom part. The ...

In this tutorial, the Numerical simulation on damage mechanics behavior of a pipeline under internal explosion in Abaqus  has been investigated. The steel pipe is modeled as a three-dimensional shell part. The soil is modeled as a three-dimensional solid part. Half of the steel pipe is placed inside the soil. ...