بایگانی برچسب: damage

In this tutorial, the Simulation bending test of a composite beam(wood-UHPC-Steel) in Abaqus has been done. The wood is modeled as a three-dimensional solid part with two layers, the top layer is in compression, and the bottom is in tension. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The ...

 In this tutorial, the Simulation under-water explosion by using the CEL method near a floating structure in Abaqus has been investigated. The aluminum hull is modeled as a three-dimensional thick shell part. The Soil, TNT, Water, and Air are modeled as three-dimensional parts inside the Eulerian domain. You can see ...

In this tutorial, the  Simulation CEL explosion near a stone wall covered with cloth, and concrete in Abaqus has been investigated. The stone wall and cloth, concrete are modeled as three-dimensional solid parts. The TNT is a solid sphere, and the Eulerian domain is a 3D body. You can see ...

In this tutorial, the Simulation of the Push-Out test on a new shear connector of the I-Shape in Abaqus has been investigated. The concrete is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. The steel beam and connector are modeled as three-dimensional solid part. ...

In this tutorial, the Simulation air blast load over a RC beam reinforced with Cloth Concrete cover in Abaqus has been done, The normal concrete core is modeled as a three-dimensional solid part. The cloth concrete part is modeled as a three-dimensional patrt. The steel bar and strips are modeled ...

In this tutorial, the Simulation CEL explosion inside the RC UHPC building in Abaqus-Damage investigation has been done The Ulta-High-Performance-Concrete(UPHC) building is modeled as a three-dimensional solid part. The reinforcements are modeled as wire part. The TNT is shpere part inside the Eulerian domain. You can see figures of the ...

In this tutorial, the Simulation compression test of a RC column with spiral CFRP with fully damaged behaviour in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The spiral CFRP is modeled as a three-dimensional solid part. The steel bar is modeled as a ...

In this tutorial, the Simulation air blast explosion over RC column with spiral strip and steel tube cover in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The spiral strips and bars are modeled as three-dimensional wire part. The steel tube as cover is ...

In this tutorial, the Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel strips and bars are modeled as three-dimensional wire part. The spiral CFRP part is modeled as a ...

In this tutorial, the Simulation Impact analysis of CFRP/PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus has been investigated. The CFRP is modeled as a three-dimensional shell part. The polyether-ether-ketone(PEEK) is modeled as a thin solid layer to protect the other layers. The silicon carbide or ceramic is ...

In this tutorial, the Simulation CEL explosion of steel-UHPC composite RC beam(column) with multiple encased steel profiles in Abaqus  has been done. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The bar and strip are modeled as three-dimensional wire parts. The steel beam core and TNT part are modeled ...

In this tutorial, the َAir blast simulation of PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus has been investigated. The polyether-ether-ketone(PEEK) is modeled as a thin solid layer to protect the other layers. The silicon carbide or ceramic is modeled as a three-dimensional solid layer at the middle. ...

In this tutorial, the  simulation of Damage prediction of concrete gravity dams subjected to underwater explosion shock loading has been done. The concrete dam is modeled as a three-dimensional solid part. The TNT, water, and air are modeled as eulerian part. The rock foundation is modeled as a three-dimensional solid ...

In this tutorial, the Simulation of concrete-encased CFST box stub columns under axial compression in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel pipes are modeled as three-dimensional solid part also,  and the steel bar and strips are modeled as the wire ...

In this tutorial, the Simulation RC beam column joint reinforced with steel plates and rods under vertical load in abaqus  has been investigated. The concrete beam-column is modeled as a three-dimensional solid part. The steel bar and strip are modeled as three-dimensional wire part. The steel plates and rods are ...

In this tutorial, the Simulation five point bending of a composite concrete beam(NSC+UHPFRC) in Abaqus has been done. The normal strength concrete beam as a cover is modeled as a three-dimensional solid part. The Ultra-High-Performace-Fiber-Reinforce-Concrete core is modeled as the a three-dimensional solid part. The steel bars and strips are ...

In this tutorial, the Simulation dynamic compression test of a RC column with UHPFRC core in Abaqus has been done, The concrete column is modeled as a three-dimensional solid part. The steel bar and strip are modeeld as three-dimensional wire paer. The Ultra-High-Performance-Fiber-Reinforce Concrete is modeled as a three-dimensional solid ...

In this tutorial, the Simulation air blast over a composite panel( Glass Epoxy-Ceramic-thermoplastic polyurethane) in Abaqus has been done. The epoxy glass composite part is modeled as a three-dimensional shell part with sixteen layers. The ceramic and polyurethane are modeled as three-dimensionalsolid part. You can see a figure of the ...

In this tutorial, the Numerical Investigation of Rigid Impact on Steel Wire Reinforced Foam Core/Composite Skin Sandwich Panel in Abaqus software has been investigated. The rigid projectile is modeled as the three-dimensional shell part. The steel reinforcements are modeled as wire part. The glass-epoxy part is modeled as a three-dimensional ...

In this tutorial, Simulation low energy impact of a rigid hammer on the wood-cement-concrete panel in Abaqus has been investigated. The panel contians three layers, top layer is wood-cement part as a soild model, the second layer is normal strenght concrete as a solid part, and third layer is wood-cement ...

In this tutorial the Simulation rocket impact and explosion over a concrete panel in Abaqus has been investigated. The concrete panel is modeled as a three-dimensional solid part. The rocket is modeled as a three-dimensional shell part, and the TNT is modeeld as a solid part. You can see a ...

In this tutorial, the Simulation air blast load over a composite panel(Aluminum+bamboo fiber) in Abaqus has been investigated. Because of the symmetry circumstance, one quarter of the geometries are modeled. The aluminum plates are modeled as three-dimensional solid part. The bamboo plate as a core of the composite panel is ...

In this tutorial, the Simulation four point bending test of a foamed concrete beam reinforced with steel bars and bamboo fiber in Abaqus has been investigated. The foamed concrete part is modeled as a three-dimensional solid part. The bamboo composite is modeled as a three-dimensional shell part with some layers. ...

In this tutorial, the Simulation air blast explosion over a steel-UHPC-steel sandwich composite beam stud connectors in Abaqus has been studied. The two steel plates with studs are modeled as three-dimensional solid part. The UHPC is modeled as a three-dimensional solid part as a core of the sandwich beam. You ...

In this tutorial, the Simulation dynamic bending test of SCS sandwich beams with UHPFRC in Abaqus has been investigated. The upper and bottom steel plates with studs are modeled as three-dimensional solid part. The middle UHPFRC is modeled as a three-dimensional solid part. You can see a figure of the ...

In this tutorial, the Simulation low energy impact on the multilayered wood panel in Abaqus-Damage investigation – has been done. The rigid ball is modeled as a three-dimensional shell part with a specific mass. Each wood panel is modeled as a three-dimensional solid part, and between the layers, the cohesive ...

In this tutorial, the Simulation dynamic four points bending of the timber wood beam reinfroced with CFRP rod and Gluein Abaqus  has been investigated. The wood beam is modeled as a three-dimensional solid part with two compression and tension sections. The adhesive and CFRP rod also is modeled as three-dimensional ...

In this tutorial, the Simulation sequential CEL explosion in the depth of soil over the RC slab in Abaqus has been investigated. The concrete slab is modeled as three-dimensional solid part, the steel reinforcement is modeled as wire part. The Soil, and TNT are modeled as three-dimensional solid parts. The ...

In this tutorial, the Simulation UHPFRC beam with initial void reinforced with CFRP rod and Expoxy under dynamic bending has been investigated. The concrete beam, CFRP rod, epoxy glu are modeled as three-dimensional solid parts. Two rigid body as a hydraulic jacks also are modeled. You can see a figure ...

In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...

In this tutorial the Simulation CEL explosion inside the CFRP composite vessel in Abaqus has been investigated. The CFRP vessel is modeled as a three-dimensional shell part in sixteen layers with different oreintation. The TNT part is modeled as a three-dimensional solid part. The surounding is modeled as an Eurlerian ...

In this tutorial the Simulation low energy impact on the concrete slab with pre tensioned bars reinforced with GFRP in Abaqus has been studeid. Concrete is modeled as a three-dimensional solid part. The GFRP part is model as plannar shell part. The steel basrs are modeled as three-dimensional wire part ...

In this tutorial the Simulation CFRP water storage tank under close air blast explosion in Abaqus has been investigaed. The CFRP tank is modeled as a three-dimensional shell part. The water is modeled as solid part and it’ll used as reference volume in load section to define the amount and ...

This tutorial investigates a Simulation air blast explosion test over a reinforced UHPC- Damage analysis. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part. The embedded bars and strips parts are modeled as a three-dimensional wire part. You can see a figure of the assembled parts below The UHPC ...

In this tutorial, the Simulation of steel projectile impact to the Reinforced-Ultra-High-Performance Concrete- Damage investigation has been investigated. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part, the embedded beam parts are modeled as a three-dimensional wire part, and finally, the steel projectile is modeled as a solid part. ...

In this package, the high and low-velocity impacts are investigated through 40 step-by-step tutorials for more than 20 hours. Through those 40 separated simulations, all aspects of the impact and collision are studied. Each tutorial contains cae, inp, step-by-step English video, and papers, also some of them have codes. Impact ...

In this tutorial, the Simulation steel bullet impact to the armor panel(Ceramic- Aluminum Foam) in Abaqus has been investigated. The steel bullet is modeled as a three-dimensional solid part. The ceramic and aluminum foam are modeled as three-dimensional solid parts. Because of the symmetry conditions, one-quarter of the whole model ...

در این ویدئوی آموزشی به شبیه سازی برخورد گلوله فولادی به پنل مرکب سرامیک-فوم آلمینیوم در نرم افزار آباکوس پرداخته ایم. هدف از این شبیه سازی بررسی تخریب هدف و گلوله در اثر سرعت بالای برخورد می باشد. گلوله فولادی به صورت سه بعدی و تغییر شکلپذیر، لایه رویی سرامیکی ...

In this tutorial, the Simulation rigid projectile impact to the ceramic-CFRP panel in Abaqus-Damage investigation – has been done. The rigid projectile is modeled as a three-dimensional shell part. The ceramic is modeled as a three-dimensional thick solid part. The CFRP or carbon fiber is modeled as a three-dimensional shell ...

در این ویدئوی آموزشی به شبیه سازی برخورد صلب به یک پنل مرکب سرامیک-CFRP و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل پارت پرتابه صلب به صورت سه بعدی و شل، پارت هدف سرامیکی به صورت یک لایه ضخیم سه بعدی و سالید و در نهایت پارت ...

In this tutorial, the Simulation SPH explosion over the composite panel( Aluminum- Metal Foam) in Abaqus-Damage investigation – has been done. The explosive part, or the TNT is modeled as a three-dimensional solid part. The aluminum sheets are modeled as three-dimensional solid parts. The Aluminum Foam as a core is ...

In this tutorial, the Simulation rigid impact to the composite panel(CFRP+TPU+AL) in Abaqus-Damage investigation – has been studied. The CFRP part is modeled as a shell part with eight layers. The Thermoplastic polyurethane is modeled as a three-dimensional solid part. The Aluminum part is modeled as a three-dimensional solid part. ...

In this tutorial, the Simulation RC beam under the repeated impact of the rigid hammer in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The steel rebar and strips are modeled as three-dimensional wire parts. The rigid hammer is modeled as a three-dimensional rigid ...

In this tutorial, the Simulation Blast response of aluminum/thermoplastic polyurethane sandwich panels in Abaqus has been investigated. The aluminum sheets are modeled as three-dimensional solid parts. The TPU is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below. History presents evidence of the ...

In this tutorial, the Numerical analysis of tilted angle shear connectors in steel-concrete composite systems in Abaqus has been investigated. The concrete block is modeled as a three-dimensional solid part. The steel beam and steel angle connector are modeled as three-dimensional solid parts. Two rigid bodies are used as boundary ...

In this tutorial, the Simulation compression test of the concrete column with and without steel reinforcement-Compression test- has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts and two rigid bodies as boundary zone and hydraulic jack. You can ...

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

In this tutorial, the damage and failure investigation of the CFRP composite military helmet under close blast explosion has been studied. The military helmet is a 3D shell part with eight different layers. The helmet part is imported to the Abaqus because of the part complexity. You can see a ...

In this tutorial, the High-velocity impact of a bullet on the RC panel- Paper validation- is investigated. The dimensions are extracted from the paper. The concrete slab is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. The bullet is modeled as a discrete ...

In this tutorial, the Simulation cyclic loading of a composite Column(UHPC + Steel box) in Abaqus has been studied. The Ultra-High-Performance Concrete column is modeled as a three-dimensional solid part. The steel box cover is modeled as a three-dimensional shell part. You can see a figure of the assembled parts ...