بایگانی برچسب: damage

Introduction to Brittle Damage Modeling in Abaqus: Johnson-Holmquist and Beissel Models Brittle damage refers to the failure mechanism observed in brittle materials such as concrete, glass, ice, and ceramics. Unlike ductile materials, which undergo significant plastic deformation before failure, brittle materials typically fail suddenly with little to no warning and ...

Introduction to Tunnel and TBM Simulation in Abaqus Abaqus is a powerful finite element analysis (FEA) software widely used in engineering and scientific research. It is particularly effective for simulating complex geotechnical problems, including tunnel construction and Tunnel Boring Machine (TBM) operations. Simulating tunnels and TBMs in Abaqus allows engineers ...

Fatigue and Cyclic Loading in Abaqus Mechanical fatigue is a phenomenon where a material undergoes progressive and localized structural damage when subjected to cyclic or fluctuating stresses, even if these stresses are below the material’s ultimate tensile strength. Over time, this repeated loading and unloading can lead to the initiation ...

Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) in Abaqus Ultra-high-performance fiber-reinforced Concrete (UHPFRC) is an advanced construction material characterized by its exceptional mechanical properties, including high compressive strength, tensile strength, and durability. UHPFRC is typically composed of a dense matrix of fine particles, high-strength cement, and steel or synthetic fibers, which enhance its ...

Introduction to Ultra-High-Performance Concrete (UHPC) in Abaqus Ultra-high-performance concrete (UHPC) is an advanced cementitious material characterized by its exceptional strength, durability, and ductility. It typically has a compressive strength exceeding 150 MPa and can reach up to 250 MPa or higher, along with superior tensile strength and resistance to environmental ...

Introduction to Masonry Wall and Structure Simulation in Abaqus Masonry walls are structural elements made from individual units (such as bricks, stones, or concrete blocks) bound together by mortar. They are widely used in construction due to their durability, thermal insulation, and aesthetic appeal. However, simulating masonry structures can be ...

Introduction to Earthquake and Seismic Analysis in Abaqus Earthquake and seismic analysis are critical aspects of structural engineering, aimed at understanding and mitigating the effects of seismic events on structures. Abaqus, a powerful finite element analysis (FEA) software developed by Dassault Systèmes, is widely used for simulating and analyzing the ...

Introduction to Bolt Analysis in Abaqus Abaqus is a powerful finite element analysis (FEA) software widely used for simulating complex mechanical systems, including bolted joints. Bolt analysis in Abaqus involves modeling the bolt, applying preload, and simulating the behavior of the bolted joint under various loading conditions. This analysis helps ...

Introduction to Dam Simulation and Analysis in Abaqus Abaqus is a powerful finite element analysis (FEA) software widely used in engineering and scientific research for simulating complex physical behaviors. When it comes to dam simulation and analysis, Abaqus provides a comprehensive suite of tools to model, analyze, and predict the performance of ...

Introduction to Rock and Stone Simulation and Analysis in Abaqus Rock and stone analysis in Abaqus software involves simulating the mechanical behavior of geological materials, such as rocks, stones, and other geomaterials, under various loading and environmental conditions. Abaqus, a powerful finite element analysis (FEA) software, is widely used in ...

Introduction to Wood Simulation and Analysis in Abaqus Wood is a complex, anisotropic material with unique mechanical properties that vary depending on grain orientation, moisture content, and other factors. Simulating and analyzing wood behavior in engineering applications requires specialized tools and methodologies. Abaqus, a powerful finite element analysis (FEA) software, ...

Introduction to Pull-Test Simulation in Abaqus Pull-test simulation in Abaqus is a computational method used to analyze the mechanical behavior of materials and structures under tensile loading. This type of simulation is commonly employed in various industries, including aerospace, automotive, and civil engineering, to predict the performance and failure mechanisms ...

Introduction to Glass Simulation and Analysis in Abaqus Abaqus, a powerful finite element analysis (FEA) software developed by Dassault Systèmes, is widely used for simulating and analyzing complex mechanical behaviors in various materials, including glass. Glass, being a brittle material with unique properties such as transparency, hardness, and low ductility, ...

In this tutorial, the Simulation of composite panels made of profiled steel skins and concrete under axial compressive load in Abaqus has been studied. The steel profile is modeled as a three-dimensional shell part. The concrete core is modeled as a three-dimensional solid part. You can see a figure of ...

In this tutorial, the Simulation durability of GFRP-SFRSC concrete adhesively bonded connection in Abaqus has been done. The GFRP beam and the steel fiber-reinforced self-compacting concrete (SFRSCC) are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below Fiber-reinforced polymer (FRP) materials are becoming increasingly considered ...

In this tutorial, the Simulation Wood-Cement wall under seismic loading in Abaqus has been investigated. The wood-cement wall is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts below Bio-sourced materials combined with a cementitious matrix ...

This tutorial investigates the Simulation of the dynamic behavior of T-shaped steel-reinforced concrete columns under high and low-impact loading in Abaqus. The concrete and steel T-shaped columns are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see figures of the assembled parts below ...

In this tutorial, the ُSimulation of the behavior of bolted shear connectors in composite slabs with steel deck in Abaqus has been studied. The steel beam, concrete, and bolts are modeled as a three-dimensional solid part. The steel deck is modeled as a shell part. You can see a figure ...

In this tutorial, the Shear-bending failure modeling of concrete ribbed slabs strengthened with UHPFRC in Abaqus has been investigated. The slab has three sections, untracked concrete, cracked concrete, and UHPFRC. All three parts are modeled as three-dimensional solid parts. the steel reinforcements are modeled as wire parts. You can see ...

In this tutorial, the Simulation composite Pipe(Aluminum-Bamboo fiber-Aluminum) under internal blast in Abaqus has been investigated. All three pipes are modeled as shell parts. You can see a figure of the assembled parts below The configuration of a composite pipe, which combines the advantages of joining two thin, stiff, and ...

In this tutorial, the finite element analysis on the seismic behavior of CFRP-strengthened seismic-composite steel-concrete frame column in Abaqus has been investigated. The concrete and steel columns are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. The CFRP box is modeled as a shell part. ...

This tutorial investigates the Simulation behavior of a new type of reinforced concrete composite slab with a joint in Abaqus. The precast plank concrete and in-situ concrete topping are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled ...

In this tutorial, the Simulation of the Kalthoff–Winkler experiment crack growth using a peridynamic model under low-velocity impact in Abaqus has been investigated. Both two- and three-dimensional models can be used to model the plate. Fracture and failure analysis has always been one of the major concerns in theoretical studies ...

In this tutorial, the Simulation of shear stud distribution on load capacity of the steel-concrete composite beam in Abaqus has been investigated. The concrete slab, steel beam, and studs are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the ...

In this tutorial, the Numerical investigation on damage characteristics of ice sheet subjected to underwater explosion load in Abaqus has been studied. The ice is modeled as a three-dimensional solid part. The air, soil, water, and TNT are modeled as an Eulerian part. You can see a figure of the ...

In this tutorial, the Flexural response and load capacity of reinforced concrete beam strengthened with reinforced mortar layer in Abaqus has been studied. The concrete and mortar are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts ...

In this tutorial, the Simulation of high-velocity impact on CFRP-Aluminum foam-Aluminum honeycomb-CFRP panel in Abaqus has been studied. The CFRP parts are modeled as three-dimensional parts with sixteen layers. The aluminum foam is modeled as a three-dimensional solid part. The aluminum honeycomb is modeled as a shell part. You can ...

In this tutorial, the ُSimulation dynamic response of concrete slab sandwich plate under close-range blast loading based on the CEL method has been studied. The concrete slab, TNT, and Eulerian domain are modeled as three-dimensional parts. The steel beams are modeled as shell parts. The steel bars are modeled as ...

In this tutorial, the Strengthening of reinforced concrete columns incorporating different configurations of stainless-steel plates has been investigated. The concrete column, steel plates, and rods are modeled as three-dimensional solid parts. The steel bar and strips are modeled as wire parts. You can see figures of the assembled parts below ...

In this tutorial, the Simulation pull-out test of a ribbed steel bar from Ultra-High-Performance-Fiber-Reinforced Concrete in Abaqus has been investigated. The steel bar is a three-dimensional model with full details. The UHPFRC part is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below ...

In this tutorial, the simulation air blast load over an aluminum sandwich structure with inner energy absorbers in Abaqus was studied. The two upper and bottom aluminum plates are modeled as dimensional shell parts. The inner energy absorbers are also modeled as three-dimensional parts. You can see a figure of ...

In this tutorial, the ُSimulation of defected RC beam with sustainable aluminum boxes incorporating ultra-high-performance concrete in Abaqus has been investigated. The concrete beam, UHPC members, and aluminum boxes are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see figures of the assembled ...

This tutorial investigates the Simulation of Shearing and bending Capacity of Concrete Beams Reinforced with Carbon Fiber Truss in Abaqus. The Ultra-High-Performance-Concrete beam is modeled as a three-dimensional solid part. The bar and strips are modeled as wire parts. The CFRP composite is modeled as a truss-shaped shell with eight ...

In this tutorial, the Simulation of low cyclic fatigue damage based on hysteresis energy on Abaqus has been investigated. The steel plated is modeled as a two-dimensional part. You can see a figure of the assembled part below. It is well known that after a number of repetitive loading cycles, ...

In this tutorial, the Analysis of composite concrete steel column using X shape steel section under compression test in Abaqus has been investigated. The steel X shape and concrete column are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of ...

This tutorial simulated a CEL explosion over a composite RC column with an X-shaped steel core in Abaqus. The concrete and steel X-shaped columns are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts, and the domain that contains explosive charge is modeled as an Eulerian ...

This example has done the finite element modeling of the pull-out test of precast wall panels connection in Abaqus. The two precast concrete walls are modeled as three-dimensional solid parts. The reinforcement steel bar and strips are modeled as wire parts. The steel bar as the connectors between two walls ...

Simulation air blast explosion over a composite panel(CFRP-Ceramic-GFPP) in Abaqus has been investigated in this tutorial. The CFRP and Glass fiber Polypropylene are modeled as shell parts with some layers. The ceramic core is modeled as a solid part. You can see a figure of the assembled parts below The ...

Simulation air blast explosion over an aluminum box reinforced with CFRP layers in Abaqus has been studied in this tutorial. The aluminum box is modeled as a three-dimensional solid part. The CFRP layers are modeled as four separated part with different orientations. You can see figures of the assembled parts ...

Finite element modeling of precast wall panel connection under monotonic loading in Abaqus has been investigated during this tutorial. Both concrete walls are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. The three solid steel bars are modeled as three-dimensional solid parts. You can see ...

Simulation SPH explosion over a composite column(Steel cover+Concrete+CFRP I shape beam) in Abaqus has been investigated in the present tutorial. The steel cover and CFRP I shape beam are modeled as three-dimensional shell parts. The concrete and TNT are modeled as three-dimensional solid parts. You can see a figure of ...

Simulation of high-velocity impact on the Ceramic-Glass polypropylene (GFPP) panel in Abaqus has been done in this tutorial. The ceramic is modeled as a three-dimensional solid part. The GFPP part is modeled as a three-dimensional shell part with some layers. You can see a figure of the assembled parts below ...

Simulation air blast load over a laced reinforced concrete with wood cover in Abaqus has been studied in this simulation. The concrete beam is modeled as a three-dimensional solid part. The laced steel reinforcements are modeled as wire parts. The wood cover is modeled as a shell part with some ...

Simulation CFRP for seismic strengthening of shear controlled RC column in Abaqus has been studied in this tutorial. The concrete column is modeled as a three-dimensional solid part, the steel reinforcements are modeled as three-dimensional wirt part, and the CFRP is modeled as a shell part. You can see a ...

Simulation of a simple composite blast protection wall system(Wood-Soil) in Abaqus has been studied in this tutorial. The wood panel is modeled as a multi-layer shell part. The soil is modeled as a solid part. You can see a figure of the assembled parts below Explosions can result from several ...

Simulation of Flexural Behavior of Laced Reinforced Concrete Beam in Abaqus has been investigated in the present study. The concrete beam is modeled as a three-dimensional solid part. The laced steel reinforcements are modeled as three-dimensional wire parts. The hydraulic jacks are modeled as rigid parts. You can see a ...

A simulation air blast explosion over a composite GLARE panel in Abaqus has been done in this tutorial. Both aluminum laters are modeled as three-dimensional solid parts. The four glass fiber layers are modeled as three-dimensional solid parts. Because of the symmetry, one-quarter of the whole model is considered. You ...

Simulation Johnson–Holmquist-II model of glass under dynamic compression load in Abaqus has been studied in this tutorial. The glass is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below Annealed glass is clear and transparent, and its fabrication is inexpensive. Because of its ...

Simulation cold spray process of a ceramic particle on the steel material in Abaqus has been done in this tutorial. The ceramic particle is modeled as a three-dimensional solid part. The steel target is modeled a solid part. The dimension of all parts are micrometer. You can see a figure ...

The numerical simulation on the high-low velocity impact response of GLAREs in Abaqus software has been investigated. The model contains metal aluminum layers and glass fiber. You can see a figure of the assembled parts below In recent decades, the demand for high‐performance materials has increased significantly in various sectors ...