Tag Archives: abaqus sph simulation

In this tutorial, the Simulation of ceramic plates as shielding for concrete blocks against projectile penetration(SPH method) has been done. The ceramic plate and Ultra-High-Performance-Concrete are modeled as three-dimensional solid parts. The bullet is modeled as a solid part. You can see a figure of the assembled parts below In ...

In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...

In this tutorial the Simulatio bird strike impact with SPH method to the composite blade in Abaqus has been investigated. The bird is modeled as the three-dimension solid part. The composite blade with eight layers is modeled as three-dimensional shell part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation ship moving through Ice-Water path in Abaqus by using SPH method has been done. The ship is imported to the Abaqus because of its complex geometry. The ice and water are modeled as a three-dimensional solid part. You can see a figure of the assembled ...

In this tutorial, the Simulation SPH explosion near RC slab by using CDP model couple with strain rate in Abaqus  has been investigated. The RC slab is modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire part. The TNT is modeled as a three-dimensional solid ...

In this tutorial, the Simulation SPH explosion inside the RC column with outer steel box cover in Abaqus has been investigated. The concrete and TNT are modeled as three-dimensional solid parts. The steel box is modeled as a three-dimensional shell part. The steel bars and strips are modeled as three-dimensional ...

In this tutorial, the Simulation water jet penetration into the stone piece in Abaqus by using SPH method  has been studied. The stone is modeled as a three-dimensional solid part. The water column is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below ...

در این ویدئوی آموزشی به شبیه سازی اثر واتر جت(SPH) روی یک قطعه سنگ و بررسی آسیب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و سنگ به صورت یک پارت سالید طراحی شده است. آب به صورت یک استوانه به صورت سه بعدی و سالید ...

In this tutorial, finite element analysis of smooth particle hydrodynamics for application to projectile impact on cementitious material has been investigated. The performance of brittle, cementitious armor panels under high-rate impact is dependent on a wide range of variables including but not limited to projectile and target geometry, impact velocity, ...

In this tutorial Simulation Smooth Particle Hydrodynamic explosion over the RC slab in Abaqus-Damage investigation- has been studied.RC slabs, as the principal components for engineering structures, have been widely used all over the world. However, blast loading, especially from contact explosion, can cause significant damage to the target structures. By ...

In this tutorial Numerical Simulation on Fracturing of Rock under Blast Using Coupled Finite Element Method and Smoothed P article Hydrodynamics has been investigated.Nowadays, drill and blast are still a common excavation technique for rock foundations and  underground caverns in the fields of hydro power, transportation and mining because these  ...

In this tutorial Simulation SPH explosion over masonry wall (micro model) in Abaqus and damage investigation has been studied.The wall is modeled with concrete bricks and concrete beam as three dimensional parts.The TNT part is modeled as sphere solid part. You can see a figure of this simulation at below To ...

In this tutorial Simulation cold spray process by using SPH method in Abaqus has been investigated. In Cold Spray, powder particles (typically 10 to 40 µm) are accelerated to very high velocities (200 to 1200 m.s-1) by a supersonic compressed gas jet at temperatures below their melting point. Upon impact with the ...

Hydroforming is a metal fabricating and forming process which allows the shaping of metals such as steel, stainless steel, copper, aluminum, and brass. This process is a cost-effective and specialized type of die molding that utilizes highly pressurized fluid to form metal. Generally there are two classifications used to describe ...