In this tutorial, the Simulation dynamic bending test of SCS sandwich beams with UHPFRC in Abaqus has been investigated. The upper and bottom steel plates with studs are modeled as three-dimensional solid part. The middle UHPFRC is modeled as a three-dimensional solid part. You can see a figure of the ...
ادامه نوشته »
In this tutorial, the Simulation air blast explosion over a timber wood beam reinforced with CFRP in Abaqus has been investigated. The two wood beam layers are modeled as three-dimensional solid parts. The CFRP sheet is modeled as a three dimensional shell part. You can see a figure of the ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی انفجار روی یک تیر چوبی دولایه تقویت شده با CFRP در نرم افزار آباکوس پرداخته ایم. مدل سازی شامل دو لایه چوب به صورت سالید و سه بعدی، یک لایه ورق کامپوزیتی به صورت شل و سه بعدی که به صورت چند لایه ...
ادامه نوشته »
In this tutorial, the Simulation low energy impact on the multilayered wood panel in Abaqus-Damage investigation – has been done. The rigid ball is modeled as a three-dimensional shell part with a specific mass. Each wood panel is modeled as a three-dimensional solid part, and between the layers, the cohesive ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی برخورد کم انرژی به پنل چوبی چندلایه در آباکوس- بررسی آسیب- پرداخته ایم. مدل سازی شامل یک پرتابه صلب و چهار لایه چوب می باشد. لایه های چوب به صورت جداگانه و به صورت سالید مدل شده اند. برای مدلسازی رفتار بین لایه ...
ادامه نوشته »
In this tutorial, the Simulation cyclic loading of a steel beam embedded in a concrete block in Abaqus has been done. The steel beam (or column) is modeled as a three-dimensional shell part. The concrete block is modeled as a three-dimensional solid part. The half of the steel beam is ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی بارگذاری سیکلی تیر فولادی تا نیمه مدفون در بتن در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل یک تیر فولادی به صورت شل(یا سالید)، و پایه بتنی به صورت سالید می باشد. تیر تا نیمه در بتن ...
ادامه نوشته »
In this tutorial, the Simulation inpact spot welding of two steel plates in Abaqus has been done. The steel flyer and base plates are modeled as three-dimensional solid part. The rigid impactor is modeled as three-dimensional shell part. You can see a figure of the assembled parts below Due to ...
ادامه نوشته »
In this tutorial, the Simulation dynamic four points bending of the timber wood beam reinfroced with CFRP rod and Gluein Abaqus has been investigated. The wood beam is modeled as a three-dimensional solid part with two compression and tension sections. The adhesive and CFRP rod also is modeled as three-dimensional ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی خمش دینامیکی چهار نقطه ای تیر چوبی تقویت شده با چسب و میلگرد CFRP در آباکوس پرداخته ایم. مدلسازی شامل تیر چوبی دو بخشی( قسمت رویی در فشار و قسمت زیرین در کشش) به صورت سالید و سه بعدی، هندسه چسب به صورت ...
ادامه نوشته »
With the growing threat and risk of attacks and explosions in densely populated urban environments, the need for advanced security glass in windows, doors, police protective galss shield, and glass partitions is also increasing. In a powerful explosion, conventional glass panes will splinter even at a great distance from the ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی انفجار در نزدیکی محافظ شیشه ای در آباکوس-بررسی آسیب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل هندسه شیشه محافظ می باشد که محل انفجار همانطور که در شکل زیر نمایش داده شده، در فاصله نزدیکی از آن قرار دارد. هدف ...
ادامه نوشته »
In this tutorial, the Numerical simulation of interlocking blocks under compression in Abaqus has been done. The blocks are modeled as three dimensional solid parts with interlocking surfaces. You can see a figure of the assembled parts below Masonry structure is one of the most predominant structures throughout the world ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی تست فشار آجرهای به هم پیوسته(Interlocking) با تعریف تماس چسبنده در آباکوس پرداخته ایم. ستون آجرهای در هم تنیده به صورت سالید و سه بعدی طراحی شده اند، که تعداد آنها و نحوه در هم تنیدگی می تواند متفاوت باشد. ملات بین آجرها ...
ادامه نوشته »
In this tutorial the Simulation Wood-Glue-CFRP beam under dynamic four points bending test in Abaqus has been investigated. The wood beam are modeled as three dimensional solid part, the adhesive parts are modeled as three-dimensional solid parts, the CFRP also si solid and the the roller are modeled as rigid ...
ادامه نوشته »
In this tutorial, the Simulation sequential CEL explosion in the depth of soil over the RC slab in Abaqus has been investigated. The concrete slab is modeled as three-dimensional solid part, the steel reinforcement is modeled as wire part. The Soil, and TNT are modeled as three-dimensional solid parts. The ...
ادامه نوشته »
In this tutorial, the Simulation UHPFRC beam with initial void reinforced with CFRP rod and Expoxy under dynamic bending has been investigated. The concrete beam, CFRP rod, epoxy glu are modeled as three-dimensional solid parts. Two rigid body as a hydraulic jacks also are modeled. You can see a figure ...
ادامه نوشته »
In this tutorial, the Simulation CEL explosion in the depth of water near the aluminum hull in Abaqus- three sea mine explosion- has been done. The domain is modeled as a three-dimension Eurlerian part. The hull is modeled as a three-dimensional shell part. The water and three TNT parts are ...
ادامه نوشته »
In this tutorial, the Simulation air blast explosion over the rebberized concrete column reinforced with green composite in Abaqus has been done. The rubberized concrete column is modeled as a three-dimensional solid part. The green composite with some layers is modeled as a three-dimensional shell part. The steel reinforcements are ...
ادامه نوشته »
In this tutorial, the Simulation dynamic bending test of a rubberized concrete beam reinforced with green composite in abaqus has been investigated. The rubberized concrete beam is modeled as a three-diensional solid part. The green composite is modeled as a three-dimensional shell part with four layups. The steel bas and ...
ادامه نوشته »
In this tutorial the Simulation ballistic impact of steel bullet to the ceramic panel reinfroced with Green Composite has been investigated. The bullet is modeled as a three-dimensional solid part, the ceramic panel as a solid part, and the green composite as a three-dimensional shell part. You can see a ...
ادامه نوشته »
In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...
ادامه نوشته »
In this tutorial the Simulatio bird strike impact with SPH method to the composite blade in Abaqus has been investigated. The bird is modeled as the three-dimension solid part. The composite blade with eight layers is modeled as three-dimensional shell part. You can see a figure of the assembled parts ...
ادامه نوشته »
In this tutorial the Simulation CEL explosion inside the CFRP composite vessel in Abaqus has been investigated. The CFRP vessel is modeled as a three-dimensional shell part in sixteen layers with different oreintation. The TNT part is modeled as a three-dimensional solid part. The surounding is modeled as an Eurlerian ...
ادامه نوشته »
In this tutorial the Simulation low energy impact on the concrete slab with pre tensioned bars reinforced with GFRP in Abaqus has been studeid. Concrete is modeled as a three-dimensional solid part. The GFRP part is model as plannar shell part. The steel basrs are modeled as three-dimensional wire part ...
ادامه نوشته »
In this tutorial the Simulation CFRP water storage tank under close air blast explosion in Abaqus has been investigaed. The CFRP tank is modeled as a three-dimensional shell part. The water is modeled as solid part and it’ll used as reference volume in load section to define the amount and ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی انفجار به روش اویلری در نزدیکی یک مخزن کامپوزیتی حاوی آب در آباکوس و بررسی آسیب مخزن پرداخته ایم. مخزن کامپوزیتی به صورت یک استوانه شل سه بعدی طراحی شده است. هندسه آب به صورت یک جسم سالید سه بعدی و همچنین فضای ...
ادامه نوشته »
In this tutorial the Simulation internal explosion of a pipe with steel supporters in Abaqus has been investigated. The steel pipe is modeled as three-dimensional solid part, it can also be shell part. The upper and bottom supports are modeled as three-dimensional solid part. You can see a figure of ...
ادامه نوشته »
This tutorial investigates a Simulation air blast explosion test over a reinforced UHPC- Damage analysis. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part. The embedded bars and strips parts are modeled as a three-dimensional wire part. You can see a figure of the assembled parts below The UHPC ...
ادامه نوشته »
In this tutorial, the Simulation of steel projectile impact to the Reinforced-Ultra-High-Performance Concrete- Damage investigation has been investigated. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part, the embedded beam parts are modeled as a three-dimensional wire part, and finally, the steel projectile is modeled as a solid part. ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی برخورد پرتابه سرعت بالا به پنل بتنی فوق توانمند در آباکوس- بررسی تخریب- پرداخته ایم. مدلسازی شامل دال بتنی فوق توانمند به صورت سه بعدی و تغییر شکلپذیر، دو لایه میلگرد به صورت سه بعدی و سیمی، و جسم ضربه زننده فولادی به ...
ادامه نوشته »
In this full lecture through eighteen tutorials with more than ten hours duration time, all aspects of welding are investigated. Each tutorial contains cae, inp, step-by-step English video, Fortran code, and papers. The lecture includes some subjects like Friction Stir Welding(Aluminum plates, steel plates, copper plates with CEL, ALE, and ...
ادامه نوشته »
In this package, the high and low-velocity impacts are investigated through 40 step-by-step tutorials for more than 20 hours. Through those 40 separated simulations, all aspects of the impact and collision are studied. Each tutorial contains cae, inp, step-by-step English video, and papers, also some of them have codes. Impact ...
ادامه نوشته »
In this lecture through ten step-by-step tutorials, many aspects of the crack growth like XFEMm H integral, and … in concrete, steel, dam, bone, and…are investigated. All the tutorials are explained from A to Z, each tutorial contains cae, inp, and step-by-step English video. All the tutorials in the package ...
ادامه نوشته »
در این پکیج آموزشی در قالب ۱۵ مثال کاربردی سعی گردیده شده است تا تمامی جوانب رشد ترک به روش های مختلف تشرریح و توضیح داده شود. در هر مثال از پکیج رشد ترک در ماده خاصی به صورت سه بعدی و یا دوبعدی در نظر گرفته شده است. مثالهای ...
ادامه نوشته »
در این پکیج آموزشی تمامی مسائل مربوط به جوشی ذوبی،مقاومتی و انفجاری موجود در سایت در قالب ۱۹ مثال جداگانه قرار داده شده است. مثال ها به صورت قدم به قدم بوده و تمامی انواع مهم جوش را مورد بررسی قرار داده است. تمامی مثالها به صورت تکی در سایت ...
ادامه نوشته »
در این پکیج سعی بر این بوده که مسائل مختلفی مربوط به تحلیل های سازه ای بتن( انواع بتن) گنجانده شود. مسائلی مربوط به تیر،ستون، اتصالات، بارگذاری تکراری، برخورد تکراری،بتن فوق توانمند و الیافی، مسائل مربوط به آسیب، تیرو ستون های کامپوزیت،…در این پکیج در قالب فایل آموزشی قرار داده ...
ادامه نوشته »
In this tutorial, the Simulation steel bullet impact to the armor panel(Ceramic- Aluminum Foam) in Abaqus has been investigated. The steel bullet is modeled as a three-dimensional solid part. The ceramic and aluminum foam are modeled as three-dimensional solid parts. Because of the symmetry conditions, one-quarter of the whole model ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی برخورد گلوله فولادی به پنل مرکب سرامیک-فوم آلمینیوم در نرم افزار آباکوس پرداخته ایم. هدف از این شبیه سازی بررسی تخریب هدف و گلوله در اثر سرعت بالای برخورد می باشد. گلوله فولادی به صورت سه بعدی و تغییر شکلپذیر، لایه رویی سرامیکی ...
ادامه نوشته »
In this tutorial, the Simulation rigid projectile impact to the ceramic-CFRP panel in Abaqus-Damage investigation – has been done. The rigid projectile is modeled as a three-dimensional shell part. The ceramic is modeled as a three-dimensional thick solid part. The CFRP or carbon fiber is modeled as a three-dimensional shell ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی برخورد صلب به یک پنل مرکب سرامیک-CFRP و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل پارت پرتابه صلب به صورت سه بعدی و شل، پارت هدف سرامیکی به صورت یک لایه ضخیم سه بعدی و سالید و در نهایت پارت ...
ادامه نوشته »
In this tutorial, the Simulation SPH explosion over the composite panel( Aluminum- Metal Foam) in Abaqus-Damage investigation – has been done. The explosive part, or the TNT is modeled as a three-dimensional solid part. The aluminum sheets are modeled as three-dimensional solid parts. The Aluminum Foam as a core is ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی انفجار به روش SPH روی یک پنل مرکب( آلمینیوم- فوم آلمینیوم) و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی می باشد. پارت ماده منفجره و یا TNT به صورت یک کره توپر و سالید در نظر گرفته ...
ادامه نوشته »
In this tutorial, the Simulation rigid impact to the composite panel(CFRP+TPU+AL) in Abaqus-Damage investigation – has been studied. The CFRP part is modeled as a shell part with eight layers. The Thermoplastic polyurethane is modeled as a three-dimensional solid part. The Aluminum part is modeled as a three-dimensional solid part. ...
ادامه نوشته »
در این ویدئوی آموزشی به شبیه سازی برخورد جسم صلب به پنل مرکب(CFRP+TPU+AL) و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و صفحه کامپوزیتی الیاف کربن به صورت هشت لایه و شل مدل شده است. لایه میانی پلی اورتان یا Thermoplastic polyurethane به ...
ادامه نوشته »
In this tutorial, the Simulation RC beam under the repeated impact of the rigid hammer in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The steel rebar and strips are modeled as three-dimensional wire parts. The rigid hammer is modeled as a three-dimensional rigid ...
ادامه نوشته »
In this tutorial, the Simulation Blast response of aluminum/thermoplastic polyurethane sandwich panels in Abaqus has been investigated. The aluminum sheets are modeled as three-dimensional solid parts. The TPU is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below. History presents evidence of the ...
ادامه نوشته »
در این یدئوی آموزشی به شبیه سازی انفجار در هوا روی یک پنل کامپوزیتی سه لایه( آلومینیوم- پلی اورتان) در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل دو لایه رویی و زیرین آلمینیومی به صورت سالید و یک لایه میانی ضخیم از Thermoplastic Polyurethane ...
ادامه نوشته »
In this tutorial, the Numerical analysis of tilted angle shear connectors in steel-concrete composite systems in Abaqus has been investigated. The concrete block is modeled as a three-dimensional solid part. The steel beam and steel angle connector are modeled as three-dimensional solid parts. Two rigid bodies are used as boundary ...
ادامه نوشته »
In this tutorial, the Simulation compression test of the concrete column with and without steel reinforcement-Compression test- has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts and two rigid bodies as boundary zone and hydraulic jack. You can ...
ادامه نوشته »
Abaqus tutorials Abaqus tutorials