در این ویدئو به شبیه سازی و محاسبه ظرفیت باربری اتصال دهنده برشی L شکل در اتصال تیر فلزی به بتن در نرم افزار آباکوس پرداخته ایم. در این تحلیل بتن، تیر فولادی و اتصال دهنده L شکل به صورت سه بعدی و تغییر شکلپذیر ترسیم شده اند. اتصال دهنده ...
ادامه نوشته »
in this tutorial Simulation air explosion over ceramic plate with lattice aluminum core in Abaqus has been investigated.The ceramic plates,two aluminum plates at the above and bottom and the lattice aluminum core are modeled as deformable three dimensional part. You can see a figure of the assembled parts at below ...
ادامه نوشته »
در این ویدئو به شبیه سازی انفجار در هوا روی یک سازه سرامیکی دارای هسته مشبک آلومینیومی در نرم افزار آباکوس پرداخته ایم.مدل شامل یک صفحه سرامیکی ،دو صفحه آلومینیومی در بالا و پایین و یک هسته مشبک در میان صفحات می باشد. تمامی پارت ها به صورت سه بعدی ...
ادامه نوشته »
In this tutorial Simulation CFRP retrofit of concrete circular column in Abaqus has been investigated. A considerable number of existing reinforced concrete columns do not meet present needs in terms of strength, ductility and durability. Repair and/or strengthening may be needed when columns are damaged under external loads, such as ...
ادامه نوشته »
در این ویدئو به شبیه سازی ستون بتنی تقویت شده با میلگرد و CFRP تحت بار عمودی در نرم افزار آباکوس پرداخته ایم.ستون بتنی به صورت پارت سه بعدی تغییر شکلپذیر،میلگردهای دایروی و طولی به صورت پارت وایر سه بعدی، صفحه کربنی دولایه به صورت شل سه بعدی و در ...
ادامه نوشته »
In this tutorial dynamic simulation of tensile test of a steel piece under axial deformation in Abaqus has been investigated. A three dimensional part like below figure is used to model steel geometry To model failure behavior of the steel piece shear and ductile damage with evolution, isotropic plasticity with ...
ادامه نوشته »
In this tutorial Numerical Simulation on Fracturing of Rock under Blast Using Coupled Finite Element Method and Smoothed P article Hydrodynamics has been investigated.Nowadays, drill and blast are still a common excavation technique for rock foundations and underground caverns in the fields of hydro power, transportation and mining because these ...
ادامه نوشته »
در این ویدئو به شبیه سازی قدم به قدم انفجار به روش SPH در میان یک توده سنگ گرانیتی در آباکوس- بررسی آسیب- پرداخته ایم.سنگ و تی ان تی به صورت پارت های سه بعدی تغییر شکلپذیر ترسیم شده اند. در شکل زیر می توانید نمایی از قرار گیری اجزا ...
ادامه نوشته »
In this tutorial Numerical simulation modeling of high velocity impact applied to reinforced concrete panel has been investigated. It is well known that concrete is much stronger in terms of compression than in tension. Because of its high com-pressive strength, and to enhance its tensile strength, tensile reinforcements are added ...
ادامه نوشته »
در این ویدئو به شبیه سازی برخورد گلوله سرعت بالا به یک پنل بتنی تقویت شده در نرم افزار آباکوس-بررسی پارامتر تخریب- پرداخته ایم.در این تحلیل بتن به صورت پارت سه بعدی تغییر شکلپذیر،گلوله به صورت پارت سه بعدی صلب و میلگردها به صورت المان وایر سه بعدی در نظر ...
ادامه نوشته »
In this tutorial Simulation creep phenomenon of a steel pipe in Abaqus has been investigated. Creep is a time-dependent deformation of a material while under an applied load that is below its yield strength. It is most often occurs at elevated temperature, but some materials creep at room temperature. Creep ...
ادامه نوشته »
در این ویدئو به شبیه سازی پدیده خزش یک لوله فلزی در نرم افزار آباکوس در پرداخته ایم.خزش (Creep) تغییر فرم دائم با گذشت زمان در یک ماده که تحت تنش یا نیروی ثابت قرار دارد، می باشد و این امر در دمای بالا (بیش از دمای تبلور مجدد) اهمیت ...
ادامه نوشته »
In this tutorial Fluid Structure Interaction simulation of human blood with coronary vessel in Abaqus has been investigated.Cardiovascular diseases represent the most frequent cause of death in modern civilization. In particular, these represent 49% of death diseases in Europe and 38% in the United States.The common index for those pathologies, ...
ادامه نوشته »
در این ویدئو به شبیه سازی سیال سازه و تعامل بین خون و رگ به صورت سه بعدی در نرم افزار آباکوس پرداخته ایم.بررسی جریان خون درون رگ ها یکی از مهمترین دغدغه های پزشکان در دهه های اخیر بوده است. امکان استفاده از نانوداروها در جریان خون و همچنین ...
ادامه نوشته »
In this tutorial water sloshing phenomenon in the cylindrical tank in Abaqus has been investigated. The effect of severe sloshing motion on global seagoing vessels is an important factor in safety design of such containers. The violent motion of fuel or liquid cargo in tanks may result in severe sloshing ...
ادامه نوشته »
در این ویدئو به شبیه سازی قدم به قدم اسلاشینگ آب در یک مخزن استوانه تحت شتاب صفحه ای در نرم افزار آباکوس پرداخته ایم.اسلاشینگ یکی از پدیده های متداول در مخازن حاوی سوخت یا مایع دارای سطح آزاد است. وجود اسلاشینگ در مخازن نیمه پر شناورها ممکن است به ...
ادامه نوشته »
In this tutorial Simulation bearing capacity of a three dimensional square foundation in Abaqus base on the Sam Helwany’s book has been investigated. To model soil and foundation a one three dimensional part is used.You can see a figure about it at below The elastic and cap plasticity with cap ...
ادامه نوشته »
در این ویدئو به شبیه سازی و محاسبه ظرفیت باربری یک پی مربعی سه بعدی در نرم افزار آباکوس به صورت قدم به قدم پرداخته ایم. مدلسازی بر اساس مثالی از کتاب Sam Helwany بوده که در آن به دلیل تقارن فقط یک چهارم مدل ایجاد شده است. مدلسازی به ...
ادامه نوشته »
In this tutorial Simulation on shock response of marine sandwich structures subjected to UNDEX loading in Abaqus has been investigated.In modern sea combat, in which strike power has increased markedly, the structures of naval ships must be designed to with-stand shock loads resulting from weapon hits.To improve the design of ...
ادامه نوشته »
در این ویدئو به شبیه سازی مرحله به مرحله انفجار زیر آب در فاصله نزدیک روی یک سازه ساندویچی فولادی در نرم افزار آباکوس به روش UNDEX پرداخته ایم. مدلسازی به صورت سه بعدی بوده و هندسه پنل ساندویچی از دو ورق رویی و زیرین به همراه هندسه مشبک ذاخلی ...
ادامه نوشته »
In this tutorial simulation end bearing capacity of a pile under rapid load in Abaqus base in the Sam Helwany book has been investigated. To model pile and soil asymmetric shell parts has been used.In geotechnical engineering, bearing capacity is the capacity of soil to support the loads applied to ...
ادامه نوشته »
در این ویدئو به شبیه سازی و محاسبه قدم به قدم ظرفیت باربری یک شمع استوانه ای بتنی در نرم افزار آباکوس پرداخته ایم.شبیه سازی به صورت تقارن محوری بوده، پارت خاک و شمع به صورت شل مدل شده اند. در شکل زیر می توانید شماتیک مسئله را مشاهده کنید. ...
ادامه نوشته »
In this tutorial Simulation Bearing Capacity Failure of a Strip Foundation in Abaqus base on the Sam Helwany’s book has been studied. Because of the symmetric condition, two dimensional shell part is used for both soil and foundation. You can see a figure of schematic at below Elastic material for ...
ادامه نوشته »
در این ویدئو به شبیه سازی مرحله به مرحله پی نواری و محاسبه ظرفیت باربری آن در نرم افزار آباکوس به صورت دو بعدی پرداخته ایم. هندسه شامل دو پارت خاک و بتن بوده که هر دو به صورت شل دو بعدی ترسیم شده اند. در این آنالیز نحوه شبیه ...
ادامه نوشته »
In this tutorial Numerical simulation of Electro-Hydraulic forming process by using acoustic method in Abaqus has been verified base on the ISI paper. Electro-hydraulic forming is one of the methods that highly considered among automotive specialists. This method is known as “high strain rate forming” method. In this process, an ...
ادامه نوشته »
در این ویدئو به شبیه سازی قدم به قدم انفجار به روش کوپل اویلری لاگرانژی در عمق خاک روی شمع فلزی در نرم افزار آباکوس پرداخته ایم.شبیه سازی به صورت سه بعدی بوده و شمع های فلزی به صورت لوله و با المان سالید،خاک و ماده منفجره به صورت اویلری ...
ادامه نوشته »
In this tutorial simulation granite stone cutting by using a rigid cutter in Abaqus has been investigated.The granite stone is modeled as three dimensional part ,the cutter and supporter are modeled as rigid body.The Abaqus CAE contains some material model for brittle materials,but they are suitable to simulate the large ...
ادامه نوشته »
در این ویدئو به شبیه سازی مرحله به مرحله برش سنگ با استفاده از یک کاتر صلب در نرم افزار آباکوس پرداخته ایم. کاتر به صورت جسم سه بعدی صلب و سنگ نیز به صورت پارت تغییر شکلپذیر سه بعدی بوده که در زیر آن یک صفحه صلب به عنوان ...
ادامه نوشته »
In this tutorial simulation CFRP jacketed reinforced concrete beam-column joints in Abaqus has been investigated.Various types of strengthening materials such as steel plates, ferrocement, and fiber reinforced polymers are available in the construction industry to be used for jacketing of the affected components, the most common being steel jackets.These types ...
ادامه نوشته »
In this simulation Finite Element simulation of Electro-Hydraulic Forming of Sheet by using time pressure curve in Abaqus has been investigated. Sheet metal forming processes are those in which force is applied to a piece of sheet metal to modify its geometry rather than remove any material. The applied force ...
ادامه نوشته »
In this tutorial Simulation concrete slab cutting by using a rigid cutter in Abaqus has been investigated.Concrete cutting is a process of controlled sawing, drilling and removal of concrete performed by skilled operators using special saws that use diamond impregnated blades. Unlike the old-fashioned dusty jack hammer method, modern concrete ...
ادامه نوشته »
In this tutorial simulation concrete beam-column joints in Abaqus has been studied. Strengthening of existing reinforced concrete structures is now a major part of the construction activity all over the world. The RCC structures constructed across the world are often found to exhibit distress and suffer damage, even before service ...
ادامه نوشته »
In this tutorial Simulation steel beam damage under cyclic loading in Abaqus standard has been investigated.Under cyclic loading conditions such as those introduced by earthquake ground motions, the local buckling is initiated in the compression flange. However, it disappears and reappears in subsequent cycles. The beam is modeled as three ...
ادامه نوشته »
In this tutorial simulation milling process in Abaqus has been investigated.Milling is a cutting process that uses a milling cutter to remove material from the surface of a workpiece. The milling cutter is a rotary cutting tool , often with multiple cutting points. As opposed to drilling, where the tool is ...
ادامه نوشته »
In this tutorial Simulation honey comb steel beam under cyclic load to extract hysteresis diagram in Abaqushas been studied.Honey Comb Castellated Beam has a deeper part than Comparable Solid Beam, which has greater resistance to deflection. Therefore, the product is most often used in Long Span applications with light and ...
ادامه نوشته »
In this tutorial Simulation of p-section concrete beams under contact explosion(CEL) conditions in Abaqus has been studied. Reinforced concrete bridges are the most common type of bridges and have a simple structure, low cost and long durability. Among these bridges, reinforced concrete bridges composed of p-section bridge components are among the ...
ادامه نوشته »
In this tutorial Prediction model of depth of penetration for alumina ceramics under garnet impact in Abaqus has been studied .The target and projectile were modeled as three dimensional parts .The JH-2 constitutive model was proposed to describe the response of ceramic materials to large strain rate. The JH-2 constitutive model ...
ادامه نوشته »
In this video Simulation steel drilling process in Abaqus has been investigated.Drilling process is one of the most required machining techniques that accounts for more than 40 % of the total material removal processes and especially has a high frequency of use in aerospace industries . It is significant to ...
ادامه نوشته »
This tutorial presents a numerical analysis of the resistance and stiffness of an aluminium-concrete beam with steel connectors. Aluminium-concrete structures are less known than steel and concrete composite structures, they do, however, have a lot of applications.Contemporary designers should look for new solutions supporting sustainable construction.Aluminium-concrete composite structures have a ...
ادامه نوشته »
In this tutorial three point bending simulation of concrete slab reinforced with bars and FRP in Abaqus has been investigated.The widespread successful use of composite materials in the automotive, naval and sporting goods industries has resulted in a technology transfer to civil infrastructure applications. Fiber-reinforced polymers (FRP) are impacting the international ...
ادامه نوشته »
Due to the universal character of the finite element method, which enables modeling of complex physical phenomena, its increasingly broad use in an interdisciplinary context, connected with the analysis of mechanical parameters of modern materials, can be observed. Among the present day areas of application of numerical analyses involving FEM, ...
ادامه نوشته »
Abaqus tutorials Abaqus tutorials