بایگانی برچسب: abaqus simulation

In this tutorial, the Fire analysis of a Steel-Timber composite beam in Abaqus has been done. Both steel and timber wood beams are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below The combination of timber and steel in a single-beam cross-section can result ...

In this tutorial, the Numerical investigation on damage characteristics of ice sheet subjected to underwater explosion load in Abaqus has been studied. The ice is modeled as a three-dimensional solid part. The air, soil, water, and TNT are modeled as an Eulerian part. You can see a figure of the ...

In this tutorial, the Flexural response and load capacity of reinforced concrete beam strengthened with reinforced mortar layer in Abaqus has been studied. The concrete and mortar are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts ...

In this tutorial, the Simulation of high-velocity impact on CFRP-Aluminum foam-Aluminum honeycomb-CFRP panel in Abaqus has been studied. The CFRP parts are modeled as three-dimensional parts with sixteen layers. The aluminum foam is modeled as a three-dimensional solid part. The aluminum honeycomb is modeled as a shell part. You can ...

In this tutorial, the Seismic analysis of geosynthetic-reinforced soil in Abaqus has been investigated. The soil is modeled as a two-dimensional part. The geosynthetic is modeled as a wire part. You can see a figure of the assembled parts below Geosynthetic-reinforced soil (GRS) structures perform well during strong earthquakes due ...

In this tutorial, the ُSimulation dynamic response of concrete slab sandwich plate under close-range blast loading based on the CEL method has been studied. The concrete slab, TNT, and Eulerian domain are modeled as three-dimensional parts. The steel beams are modeled as shell parts. The steel bars are modeled as ...

In this tutorial, the Strengthening of reinforced concrete columns incorporating different configurations of stainless-steel plates has been investigated. The concrete column, steel plates, and rods are modeled as three-dimensional solid parts. The steel bar and strips are modeled as wire parts. You can see figures of the assembled parts below ...

In this tutorial, the Simulation pull-out test of a ribbed steel bar from Ultra-High-Performance-Fiber-Reinforced Concrete in Abaqus has been investigated. The steel bar is a three-dimensional model with full details. The UHPFRC part is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below ...

In this tutorial, the Seismic analysis of a steel building with the axial dampers in Abaqus has been investigated. The steel building, beams, columns, and connectors are modeled as wire parts. You can see a figure of the assembled parts below In the present scenario, the whole world is susceptible ...

In this tutorial, the simulation air blast load over an aluminum sandwich structure with inner energy absorbers in Abaqus was studied. The two upper and bottom aluminum plates are modeled as dimensional shell parts. The inner energy absorbers are also modeled as three-dimensional parts. You can see a figure of ...

In this tutorial, the ُSimulation of defected RC beam with sustainable aluminum boxes incorporating ultra-high-performance concrete in Abaqus has been investigated. The concrete beam, UHPC members, and aluminum boxes are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see figures of the assembled ...

This tutorial investigates the Simulation of Shearing and bending Capacity of Concrete Beams Reinforced with Carbon Fiber Truss in Abaqus. The Ultra-High-Performance-Concrete beam is modeled as a three-dimensional solid part. The bar and strips are modeled as wire parts. The CFRP composite is modeled as a truss-shaped shell with eight ...

In this tutorial, the Simulation of low cyclic fatigue damage based on hysteresis energy on Abaqus has been investigated. The steel plated is modeled as a two-dimensional part. You can see a figure of the assembled part below. It is well known that after a number of repetitive loading cycles, ...

In this tutorial, the Analysis of composite concrete steel column using X shape steel section under compression test in Abaqus has been investigated. The steel X shape and concrete column are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of ...

In this tutorial, the Simulation Exposed column base plate connections in moment frames in Abaqus have been done. The steel column, bolts, steel bed plate, and concrete foundation are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below In low and mid-rise steel structures ...

In this tutorial, the Simulation of water sloshing in a cylindrical tank under seismic loading with the Acoustic method in Abaqus has been investigated, besides the seismic loading analysis, the frequency model is done to extract the frequency of the tank and acoustic water part. The storage steel tank is ...

Simulation of the Cold Spray process of an ABS material by using the CEL method in Abaqus has been investigated in the present model. The ABS is an amorphous polymer comprised of three monomers, acrylonitrile, butadiene, and styrene. ABS is most commonly polymerized through the emulsification process or the expert ...

This tutorial simulated a CEL explosion over a composite RC column with an X-shaped steel core in Abaqus. The concrete and steel X-shaped columns are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts, and the domain that contains explosive charge is modeled as an Eulerian ...

This example has done the finite element modeling of the pull-out test of precast wall panels connection in Abaqus. The two precast concrete walls are modeled as three-dimensional solid parts. The reinforcement steel bar and strips are modeled as wire parts. The steel bar as the connectors between two walls ...

Simulation air blast explosion over a composite panel(CFRP-Ceramic-GFPP) in Abaqus has been investigated in this tutorial. The CFRP and Glass fiber Polypropylene are modeled as shell parts with some layers. The ceramic core is modeled as a solid part. You can see a figure of the assembled parts below The ...

Finite Element Analysis on the Mechanical Performance of the Middle Long CFST Column with an Inner I-shaped CFRP Profile under Axial Loading has been done in this tutorial. The steel box is modeled as a shell part. The inner concrete is modeled as a three-dimensional solid part. The CFRP I-shape ...

Simulation air blast explosion over an aluminum box reinforced with CFRP layers in Abaqus has been studied in this tutorial. The aluminum box is modeled as a three-dimensional solid part. The CFRP layers are modeled as four separated part with different orientations. You can see figures of the assembled parts ...

Finite element modeling of precast wall panel connection under monotonic loading in Abaqus has been investigated during this tutorial. Both concrete walls are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. The three solid steel bars are modeled as three-dimensional solid parts. You can see ...

Simulation SPH explosion over a composite column(Steel cover+Concrete+CFRP I shape beam) in Abaqus has been investigated in the present tutorial. The steel cover and CFRP I shape beam are modeled as three-dimensional shell parts. The concrete and TNT are modeled as three-dimensional solid parts. You can see a figure of ...

Simulation static modeling of masonry wall(brick+mortar) under compression load in Abaqus has been studied in the present tutorial. Mortar is modeled as a three-dimensional solid part. Bricks are modeled as as three-dimensional solid parts. You can see a figure of the assembled parts below Masonry wall systems are building systems that ...

Simulation of high-velocity impact on the Ceramic-Glass polypropylene (GFPP) panel in Abaqus has been done in this tutorial. The ceramic is modeled as a three-dimensional solid part. The GFPP part is modeled as a three-dimensional shell part with some layers. You can see a figure of the assembled parts below ...

Four-point bending test of an aluminum pipe reinforced with four CFRP layers in Abaqus has been modeled in this tutorial. The aluminum pipe is modeled as a solid part, the CFRP pipes are modeled as four seperate shell parts. Cohesive interaction property is considered among all layers. You can see ...

Simulation air blast load over a laced reinforced concrete with wood cover in Abaqus has been studied in this simulation. The concrete beam is modeled as a three-dimensional solid part. The laced steel reinforcements are modeled as wire parts. The wood cover is modeled as a shell part with some ...

Simulation CFRP for seismic strengthening of shear controlled RC column in Abaqus has been studied in this tutorial. The concrete column is modeled as a three-dimensional solid part, the steel reinforcements are modeled as three-dimensional wirt part, and the CFRP is modeled as a shell part. You can see a ...

Simulation of a simple composite blast protection wall system(Wood-Soil) in Abaqus has been studied in this tutorial. The wood panel is modeled as a multi-layer shell part. The soil is modeled as a solid part. You can see a figure of the assembled parts below Explosions can result from several ...

Simulation of Depositing Al-Based Metallic Coatings onto Polymer Substrates by Cold Spray in Abaqus has been investigated in the present tutorial. The  aluminum particles are modeled as three-dimensional solid part in Micro scale. The polyetheretherketone(PEEK) polymer is modeled as a three-dimensional solid part. You can see a figure of the ...

Simulation of Flexural Behavior of Laced Reinforced Concrete Beam in Abaqus has been investigated in the present study. The concrete beam is modeled as a three-dimensional solid part. The laced steel reinforcements are modeled as three-dimensional wire parts. The hydraulic jacks are modeled as rigid parts. You can see a ...

A simulation air blast explosion over a composite GLARE panel in Abaqus has been done in this tutorial. Both aluminum laters are modeled as three-dimensional solid parts. The four glass fiber layers are modeled as three-dimensional solid parts. Because of the symmetry, one-quarter of the whole model is considered. You ...

Simulation Johnson–Holmquist-II model of glass under dynamic compression load in Abaqus has been studied in this tutorial. The glass is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below Annealed glass is clear and transparent, and its fabrication is inexpensive. Because of its ...

در این ویدئوی آموزشی به شبیه سازی تست فشار دینامیکی شیشه و خرد شدگی آن در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه شیشه به صورت استوانه سه بعدی و تو پر می باشد. اجزا صلب نیز به صورت شل در نقش جک هیدرولیک و نگهدارنده طراحی شده اند. ...

Simulation cold spray process of a ceramic particle on the steel material in Abaqus has been done in this tutorial. The ceramic particle is modeled as a three-dimensional solid part. The steel target is modeled a solid part. The dimension of all parts are micrometer. You can see a figure ...

The numerical simulation on the high-low velocity impact response of GLAREs in Abaqus software has been investigated. The model contains metal aluminum layers and glass fiber. You can see a figure of the assembled parts below In recent decades, the demand for high‐performance materials has increased significantly in various sectors ...

The simulation of non-Newtonian water flow impact on the rigid barrier in Abaqus- Smooth Particle Hydrodynamic has been investigated. The water is modeled as a three-dimensional solid part with noe-Newtonian behavior. You can see a figure of the assembled parts below A non-Newtonian fluid is a fluid that does not ...

Numerical simulation of concrete-filled double skin steel tubular (CFDST) structure subjected to underwater explosion loading in Abaqus has been don in this example. The concrete column is modeled as a three-dimensional solid part. The inner and outer steel tubes are modeled as shell parts. The air, water, and TNT are ...

The Cyclic Test Simulation of Concrete-Filled Steel Column in Abaqus-Validation Analysis has been done in this tutorial. The steel box column, ribs, and stiffener plates are modeled as three-dimensional shell parts. The two concrete blocks are modeled as three-dimensional solid parts. You can see the figures of the assembled parts ...

In this tutorial, the Simulation of the CFRP blanket effect on reducing the deformation of buried pipelines exposed to the subsurface explosion in Abaqus has been investigated. The air, soil, and TNT are modeled as three-dimensional parts inside an Eulerian part. The steel pipe is modeled as a three-dimensional part. ...

In this tutorial, the Simulation hollow-core slab under fire conditions and four-point bending in Abaqus has been investigated. Precast/prestressed concrete hollow core (PCHC) slabs with a reduction in self-weight due to longitudinal voids, and without shear reinforcement due to the extrusion method are most susceptible to shear failure. When subjected ...

In this tutorial, the Simulation of rigid impact on the composite panel(Aluminum and Wood) in Abaqus has been investigated. The rigid impactor is modeled as the shell part. The aluminum plate is modeled as a three-dimensional solid part. The wood layer is modeled as a three-dimensional part with some layers. ...

In this tutorial, the Simulation bending test of the steel-concrete composite beam in SRC structures considering bond-slip behavior in Abaqus has been investigated. The steel-concrete composite beam is modeled as a three-dimensional solid part. The steel reinforcements are modeled as the wire parts. You can see a figure of the ...

In this tutorial, the Simulation of ceramic plates as shielding for concrete blocks against projectile penetration(SPH method) has been done. The ceramic plate and Ultra-High-Performance-Concrete are modeled as three-dimensional solid parts. The bullet is modeled as a solid part. You can see a figure of the assembled parts below In ...

In this tutorial, the Simulation of the UHPC beam-column joint reinforced with steel angle and bolts in Abaqus has been investigated. The Ulta-High-Performance-Concrete beam-column joint is modeled as a three-dimensional solid part. The steel bar and strips are modeled as three-dimensional wire parts. The steel angle, plates, and bolts are ...

In this tutorial, the Simulation deposition behavior of multi-particle impact in the cold spraying process in Abaqus has been investigated. The aluminum particles are modeled as three-dimensional solid parts. The aluminum target also is modeled as a three-dimensional solid part. You can see a figure of the assembled parts In ...

In this tutorial, the Simulation load bearing capacity of a composite joint between a reinforced concrete column and a steel beam in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel beam and column are modeled as three-dimensional solid parts. The steel bar ...

In this tutorial, the Simulation dynamic compression test of a steel column with the UHPC core in interaction with a concrete foundation in Abaqus has been investigated. The concrete foundation and column are modeled as three-dimensional solid parts. The steel column and steel stiffener angles are modeled as shell parts. ...

In this tutorial, the Simulation and Analysis of the Seismic Behavior of a Prefabricated Semirigid Steel Frame with X-Shaped Brace in Abaqus has been done. The steel column and beam are modeled as three-dimensional parts. The steel plate as stiffeners and braces are modeled as three-dimensional parts. You can see ...