تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: abaqus johnson holmquist model

بایگانی برچسب: abaqus johnson holmquist model

Numerical investigation on damage characteristics of ice sheet subjected to underwater explosion load in Abaqus

In this tutorial, the Numerical investigation on damage characteristics of ice sheet subjected to underwater explosion load in Abaqus has been studied. The ice is modeled as a three-dimensional solid part. The air, soil, water, and TNT are modeled as an Eulerian part. You can see a figure of the ...

ادامه نوشته »

ُSimulation dynamic response of concrete slab sandwich plate under close-range blast loading based on the CEL method

In this tutorial, the ُSimulation dynamic response of concrete slab sandwich plate under close-range blast loading based on the CEL method has been studied. The concrete slab, TNT, and Eulerian domain are modeled as three-dimensional parts. The steel beams are modeled as shell parts. The steel bars are modeled as ...

ادامه نوشته »

Strengthening of reinforced concrete columns incorporating different configurations of stainless-steel plates

In this tutorial, the Strengthening of reinforced concrete columns incorporating different configurations of stainless-steel plates has been investigated. The concrete column, steel plates, and rods are modeled as three-dimensional solid parts. The steel bar and strips are modeled as wire parts. You can see figures of the assembled parts below ...

ادامه نوشته »

Simulation pull-out test of a ribbed steel bar from Ultra-High-Performance-Fiber-Reinforced Concrete in Abaqus

In this tutorial, the Simulation pull-out test of a ribbed steel bar from Ultra-High-Performance-Fiber-Reinforced Concrete in Abaqus has been investigated. The steel bar is a three-dimensional model with full details. The UHPFRC part is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below ...

ادامه نوشته »

Simulation air blast load over aluminum sandwich structure with inner energy absorbers in abaqus

In this tutorial, the simulation air blast load over an aluminum sandwich structure with inner energy absorbers in Abaqus was studied. The two upper and bottom aluminum plates are modeled as dimensional shell parts. The inner energy absorbers are also modeled as three-dimensional parts. You can see a figure of ...

ادامه نوشته »

Simulation CEL explosion over a composite RC column with X-shaped steel core in Abaqus

This tutorial simulated a CEL explosion over a composite RC column with an X-shaped steel core in Abaqus. The concrete and steel X-shaped columns are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts, and the domain that contains explosive charge is modeled as an Eulerian ...

ادامه نوشته »

Simulation air blast explosion over a composite panel(CFRP-Ceramic-GFPP) in Abaqus

Simulation air blast explosion over a composite panel(CFRP-Ceramic-GFPP) in Abaqus has been investigated in this tutorial. The CFRP and Glass fiber Polypropylene are modeled as shell parts with some layers. The ceramic core is modeled as a solid part. You can see a figure of the assembled parts below The ...

ادامه نوشته »

Simulation air blast explosion over an aluminum box reinforced with CFRP layers in Abaqus

Simulation air blast explosion over an aluminum box reinforced with CFRP layers in Abaqus has been studied in this tutorial. The aluminum box is modeled as a three-dimensional solid part. The CFRP layers are modeled as four separated part with different orientations. You can see figures of the assembled parts ...

ادامه نوشته »

Simulation SPH explosion over a composite column(Steel cover+Concrete+CFRP I shape beam) in Abaqus

Simulation SPH explosion over a composite column(Steel cover+Concrete+CFRP I shape beam) in Abaqus has been investigated in the present tutorial. The steel cover and CFRP I shape beam are modeled as three-dimensional shell parts. The concrete and TNT are modeled as three-dimensional solid parts. You can see a figure of ...

ادامه نوشته »

Simulation of high-velocity impact on the Ceramic-Glass polypropylene (GFPP) panel in Abaqus

Simulation of high-velocity impact on the Ceramic-Glass polypropylene (GFPP) panel in Abaqus has been done in this tutorial. The ceramic is modeled as a three-dimensional solid part. The GFPP part is modeled as a three-dimensional shell part with some layers. You can see a figure of the assembled parts below ...

ادامه نوشته »

Simulation of Depositing Al-Based Metallic Coatings onto Polymer Substrates by Cold Spray in Abaqus

Simulation of Depositing Al-Based Metallic Coatings onto Polymer Substrates by Cold Spray in Abaqus has been investigated in the present tutorial. The  aluminum particles are modeled as three-dimensional solid part in Micro scale. The polyetheretherketone(PEEK) polymer is modeled as a three-dimensional solid part. You can see a figure of the ...

ادامه نوشته »

Simulation air blast explosion over a composite GLARE panel in Abaqus

A simulation air blast explosion over a composite GLARE panel in Abaqus has been done in this tutorial. Both aluminum laters are modeled as three-dimensional solid parts. The four glass fiber layers are modeled as three-dimensional solid parts. Because of the symmetry, one-quarter of the whole model is considered. You ...

ادامه نوشته »

Simulation Johnson–Holmquist-II model of glass under dynamic compression load in Abaqus

Simulation Johnson–Holmquist-II model of glass under dynamic compression load in Abaqus has been studied in this tutorial. The glass is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below Annealed glass is clear and transparent, and its fabrication is inexpensive. Because of its ...

ادامه نوشته »

شبیه سازی تست فشار دینامیکی شیشه و خرد شدگی آن در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی تست فشار دینامیکی شیشه و خرد شدگی آن در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه شیشه به صورت استوانه سه بعدی و تو پر می باشد. اجزا صلب نیز به صورت شل در نقش جک هیدرولیک و نگهدارنده طراحی شده اند. ...

ادامه نوشته »

Numerical simulation on high-low velocity impact response of GLAREs

The numerical simulation on the high-low velocity impact response of GLAREs in Abaqus software has been investigated. The model contains metal aluminum layers and glass fiber. You can see a figure of the assembled parts below In recent decades, the demand for high‐performance materials has increased significantly in various sectors ...

ادامه نوشته »

Numerical simulation of concrete-filled double skin steel tubular (CFDST) structure subjected to underwater explosion loading in Abaqus

Numerical simulation of concrete-filled double skin steel tubular (CFDST) structure subjected to underwater explosion loading in Abaqus has been don in this example. The concrete column is modeled as a three-dimensional solid part. The inner and outer steel tubes are modeled as shell parts. The air, water, and TNT are ...

ادامه نوشته »

Simulation of the CFRP blanket effect on reducing the deformation of buried pipelines exposed to the subsurface explosion in Abaqus

In this tutorial, the Simulation of the CFRP blanket effect on reducing the deformation of buried pipelines exposed to the subsurface explosion in Abaqus has been investigated. The air, soil, and TNT are modeled as three-dimensional parts inside an Eulerian part. The steel pipe is modeled as a three-dimensional part. ...

ادامه نوشته »

Simulation of rigid impact on the composite panel(Aluminum and Wood) in Abaqus-Damage investigation

In this tutorial, the Simulation of rigid impact on the composite panel(Aluminum and Wood) in Abaqus has been investigated. The rigid impactor is modeled as the shell part. The aluminum plate is modeled as a three-dimensional solid part. The wood layer is modeled as a three-dimensional part with some layers. ...

ادامه نوشته »

Using ceramic plates as shielding for concrete blocks against projectile penetration-SPH method

In this tutorial, the Simulation of ceramic plates as shielding for concrete blocks against projectile penetration(SPH method) has been done. The ceramic plate and Ultra-High-Performance-Concrete are modeled as three-dimensional solid parts. The bullet is modeled as a solid part. You can see a figure of the assembled parts below In ...

ادامه نوشته »

Simulation pullout behavior of a silicon carbide(ceramic) nail from the bone in Abaqus

In this tutorial, the Simulation pullout behavior of a silicon carbide (ceramic) nail from the bone in Abaqus has been investigated with two interaction methods. The ceramic nail or screw is a three-dimensional solid part. The bone is modeled as a three-dimensional solid part. Because of the part’s difficulties, they ...

ادامه نوشته »

Simulation air blast load over a reinforced concrete beam with spiral GFRP bar in Abaqus

In this tutorial, the Simulation air blast load over a reinforced concrete beam with a spiral GFRP bar in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part, the spiral GFRP is a solid part also. The steel reinforcements are modeled as three-dimensional wire parts. ...

ادامه نوشته »

Investigation on the repeated impact responses of circular concrete-filled double-tube (CFDT) members in Abaqus

In this tutorial, the Investigation on the repeated impact responses of circular concrete-filled double-tube (CFDT) members in Abaqus have been studied. The two concrete cores are modeled as three-dimensional solid parts. The two steel tubes are modeled as three-dimensional solid parts. The rigid hammer as an impact is used also. ...

ادامه نوشته »

Simulation air blast explosion over a composite panel(Silica glass-Aluminum-CFRP) in Abaqus

In this tutorial, the Simulation air blast explosion over a composite panel(Silica glass-Aluminum-CFRP) in Abaqus has been investigated. The silica glass is modeled as a three-dimensional part. The aluminum as the middle layer is modeled as a three-dimensional solid part. The CFRP as the backplate is modeled as a shell ...

ادامه نوشته »

Simulation of a steel bullet impact on the composite panel(Boron carbide-CFRP-Gelatin) in Abaqus

In this tutorial, the Simulation of a steel bullet impact on the composite panel (Boron carbide-CFRP-Gelatin) in Abaqus has been investigated. The bullet is modeled as a three-dimensional solid part. The boron carbide and gelatin are modeled as three-dimensional solid parts. The CFRP is modeled as a shell with eight ...

ادامه نوشته »

Simulation of a CEL large-scale bomb explosion(Nuclear detonation) near a building in Abaqus

In this tutorial, the Simulation of a CEL large-scale bomb explosion (Nuclear detonation) near a building in Abaqus has been investigated. A nuclear explosion releases vast amounts of energy in the form of blasts, heat, and radiation. An enormous Shockwave reaches speeds of many hundreds of kilometers an hour. The blast ...

ادامه نوشته »

Simulation air blast analysis of a composite column(wood-concrete-CFRP) in Abaqus

In this tutorial, the Simulation air blast analysis of a composite column(wood-concrete-CFRP) in Abaqus has been investigated. The wood is modeled as a three-dimensional solid part with two layers of tension and compression. The concrete is modeled as a three-dimensional solid part. The steel bars and strips are modeled as ...

ادامه نوشته »

Simulation CEL explosion inside the RC UHPC building in Abaqus-Damage investigation

In this tutorial, the Simulation CEL explosion inside the RC UHPC building in Abaqus-Damage investigation has been done The Ulta-High-Performance-Concrete(UPHC) building is modeled as a three-dimensional solid part. The reinforcements are modeled as wire part. The TNT is shpere part inside the Eulerian domain. You can see figures of the ...

ادامه نوشته »

Simulation air blast explosion over RC column with spiral strip and steel tube cover in Abaqus

In this tutorial, the Simulation air blast explosion over RC column with spiral strip and steel tube cover in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The spiral strips and bars are modeled as three-dimensional wire part. The steel tube as cover is ...

ادامه نوشته »

Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus

In this tutorial, the Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel strips and bars are modeled as three-dimensional wire part. The spiral CFRP part is modeled as a ...

ادامه نوشته »

Simulation Impact analysis of CFRP/PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus

In this tutorial, the Simulation Impact analysis of CFRP/PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus has been investigated. The CFRP is modeled as a three-dimensional shell part. The polyether-ether-ketone(PEEK) is modeled as a thin solid layer to protect the other layers. The silicon carbide or ceramic is ...

ادامه نوشته »

Simulation CEL explosion of steel-UHPC composite RC beam(column) with multiple encased steel profiles in Abaqus

In this tutorial, the Simulation CEL explosion of steel-UHPC composite RC beam(column) with multiple encased steel profiles in Abaqus  has been done. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The bar and strip are modeled as three-dimensional wire parts. The steel beam core and TNT part are modeled ...

ادامه نوشته »

َAir blast simulation of PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus

In this tutorial, the َAir blast simulation of PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus has been investigated. The polyether-ether-ketone(PEEK) is modeled as a thin solid layer to protect the other layers. The silicon carbide or ceramic is modeled as a three-dimensional solid layer at the middle. ...

ادامه نوشته »

Damage prediction of concrete gravity dams subjected to two underwater explosion shock loading

In this tutorial, the  simulation of Damage prediction of concrete gravity dams subjected to underwater explosion shock loading has been done. The concrete dam is modeled as a three-dimensional solid part. The TNT, water, and air are modeled as eulerian part. The rock foundation is modeled as a three-dimensional solid ...

ادامه نوشته »

Numerical Investigation of Rigid Impact on Steel Wire Reinforced Foam Core/Composite Skin Sandwich Panel

In this tutorial, the Numerical Investigation of Rigid Impact on Steel Wire Reinforced Foam Core/Composite Skin Sandwich Panel in Abaqus software has been investigated. The rigid projectile is modeled as the three-dimensional shell part. The steel reinforcements are modeled as wire part. The glass-epoxy part is modeled as a three-dimensional ...

ادامه نوشته »

Simulation air blast load over a composite panel(Aluminum+bamboo fiber) in Abaqus

In this tutorial, the Simulation air blast load over a composite panel(Aluminum+bamboo fiber) in Abaqus has been investigated. Because of the symmetry circumstance, one quarter of the geometries are modeled. The aluminum plates are modeled as three-dimensional solid part. The bamboo plate as a core of the composite panel is ...

ادامه نوشته »

Simulation air blast explosion over a steel-UHPC-steel sandwich composite beam stud connectors in Abaqus

In this tutorial, the Simulation air blast explosion over a steel-UHPC-steel sandwich composite beam stud connectors in Abaqus has been studied. The two steel plates with studs are modeled as three-dimensional solid part. The UHPC is modeled as a three-dimensional solid part as a core of the sandwich beam. You ...

ادامه نوشته »

Simulation high-velocity impact on the Aluminum-Bamboo sandwich panel in Abaqus

In this tutorial, the Simulation high-velocity impact on the Aluminum-Bamboo sandwich panel in Abaqus has been done. The aluminum plate is modeled as a three-dimensional solid part. The bamboo plate is modeled as a shell part with thirty two layers with different fiber angle. The projectile is modeled as a ...

ادامه نوشته »

Simulation close explosion test of a glass shield in Abaqus

With the growing threat and risk of attacks and explosions in densely populated urban environments, the need for advanced security glass in windows, doors, police protective galss shield, and glass partitions is also increasing. In a powerful explosion, conventional glass panes will splinter even at a great distance from the ...

ادامه نوشته »

شبیه سازی انفجار در نزدیکی محافظ شیشه ای در آباکوس-بررسی آسیب

در این ویدئوی آموزشی به شبیه سازی انفجار در نزدیکی محافظ شیشه ای در آباکوس-بررسی آسیب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل هندسه شیشه محافظ می باشد که محل انفجار همانطور که در شکل زیر نمایش داده شده، در فاصله نزدیکی از آن قرار دارد. هدف ...

ادامه نوشته »

Simulation sequential CEL explosion in the depth of soil over the RC slab in Abaqus

In this tutorial, the Simulation sequential CEL explosion in the depth of soil over the RC slab in Abaqus has been investigated. The concrete slab is modeled as three-dimensional solid part, the steel reinforcement is modeled as wire part. The Soil, and TNT are modeled as three-dimensional solid parts. The ...

ادامه نوشته »

Simulation CEL explosion in the depth of water near the aluminum hull in Abaqus- three sea mine explosion

In this tutorial, the Simulation CEL explosion in the depth of water near the aluminum hull in Abaqus- three sea mine explosion- has been done. The domain is modeled as a three-dimension Eurlerian part. The hull is modeled as a three-dimensional shell part. The water and three TNT parts are ...

ادامه نوشته »

Simulation ballistic impact of steel bullet to the ceramic panel reinfroced with Green Composite

In this tutorial the Simulation ballistic impact of steel bullet to the ceramic panel reinfroced with Green Composite has been investigated. The bullet is modeled as a three-dimensional solid part, the ceramic panel as a solid part, and the green composite as a three-dimensional shell part. You can see a ...

ادامه نوشته »

Explosion simulation near the reinforced concrete wall with green composite-SPH method

In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...

ادامه نوشته »

Simulation air blast explosion test over a reinforced UHPC- Damage analysis

This tutorial investigates a Simulation air blast explosion test over a reinforced UHPC- Damage analysis. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part. The embedded bars and strips parts are modeled as a three-dimensional wire part. You can see a figure of the assembled parts below The UHPC ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo