تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: Abaqus free tutorial

بایگانی برچسب: Abaqus free tutorial

Flexural response and load capacity of reinforced concrete beams strengthened with reinforced mortar layer in Abaqus

In this tutorial, the Flexural response and load capacity of reinforced concrete beam strengthened with reinforced mortar layer in Abaqus has been studied. The concrete and mortar are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts ...

ادامه نوشته »

Strengthening of reinforced concrete columns incorporating different configurations of stainless-steel plates

In this tutorial, the Strengthening of reinforced concrete columns incorporating different configurations of stainless-steel plates has been investigated. The concrete column, steel plates, and rods are modeled as three-dimensional solid parts. The steel bar and strips are modeled as wire parts. You can see figures of the assembled parts below ...

ادامه نوشته »

Simulation of defected RC beam with sustainable aluminum boxes incorporating ultra-high-performance concrete in Abaqus

In this tutorial, the ُSimulation of defected RC beam with sustainable aluminum boxes incorporating ultra-high-performance concrete in Abaqus has been investigated. The concrete beam, UHPC members, and aluminum boxes are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see figures of the assembled ...

ادامه نوشته »

Finite element modeling of pull-out test of precast wall panels connection in Abaqus

This example has done the finite element modeling of the pull-out test of precast wall panels connection in Abaqus. The two precast concrete walls are modeled as three-dimensional solid parts. The reinforcement steel bar and strips are modeled as wire parts. The steel bar as the connectors between two walls ...

ادامه نوشته »

Simulation deposition behavior of multi-particle impact in cold spraying process in Abaqus

In this tutorial, the Simulation deposition behavior of multi-particle impact in the cold spraying process in Abaqus has been investigated. The aluminum particles are modeled as three-dimensional solid parts. The aluminum target also is modeled as a three-dimensional solid part. You can see a figure of the assembled parts In ...

ادامه نوشته »

Simulation load bearing capacity of a composite joint between a reinforced concrete column and a steel beam in Abaqus

In this tutorial, the Simulation load bearing capacity of a composite joint between a reinforced concrete column and a steel beam in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel beam and column are modeled as three-dimensional solid parts. The steel bar ...

ادامه نوشته »

Simulation cyclic loading of a steel beam-column joint with welded steel angle and stiffeners in Abaqus

In this tutorial, the Simulation cyclic loading of a steel beam-column joint with welded steel angle and stiffeners in Abaqus. Box column, steel beam angles, and stiffeners are modeled as the three-dimensional solid part. If a structural steel member is subjected to a cyclically varying load of sufficient amplitude it ...

ادامه نوشته »

Cyclic behavior of exposed base plates with extended anchor bolts in Abaqus

Column base connections are among the most critical components of Steel Moment Frames, their behavior profoundly influences the overall performance of SMFs. Early investigations on Column-base connections alongside remarkable experimental programs on large-scale specimens. have provided insight into their behavior and failure modes. These tests led to the development of ...

ادامه نوشته »

Simulation air blast load over a reinforced concrete beam with spiral GFRP bar in Abaqus

In this tutorial, the Simulation air blast load over a reinforced concrete beam with a spiral GFRP bar in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part, the spiral GFRP is a solid part also. The steel reinforcements are modeled as three-dimensional wire parts. ...

ادامه نوشته »

Simulation of a CEL large-scale bomb explosion(Nuclear detonation) near a building in Abaqus

In this tutorial, the Simulation of a CEL large-scale bomb explosion (Nuclear detonation) near a building in Abaqus has been investigated. A nuclear explosion releases vast amounts of energy in the form of blasts, heat, and radiation. An enormous Shockwave reaches speeds of many hundreds of kilometers an hour. The blast ...

ادامه نوشته »

Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus

In this tutorial, the Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel strips and bars are modeled as three-dimensional wire part. The spiral CFRP part is modeled as a ...

ادامه نوشته »

Simulation four point bending test of a foamed concrete beam reinforced with steel bars and bamboo fiber in Abaqus

In this tutorial, the Simulation four point bending test of a foamed concrete beam reinforced with steel bars and bamboo fiber in Abaqus has been investigated. The foamed concrete part is modeled as a three-dimensional solid part. The bamboo composite is modeled as a three-dimensional shell part with some layers. ...

ادامه نوشته »

Simulation CEL explosion in the depth of water near the aluminum hull in Abaqus- three sea mine explosion

In this tutorial, the Simulation CEL explosion in the depth of water near the aluminum hull in Abaqus- three sea mine explosion- has been done. The domain is modeled as a three-dimension Eurlerian part. The hull is modeled as a three-dimensional shell part. The water and three TNT parts are ...

ادامه نوشته »

Simulation dynamic bending test of a rubberized concrete beam reinforced with green composite

In this tutorial, the Simulation dynamic bending test of a rubberized concrete beam reinforced with green composite  in abaqus has been investigated. The rubberized concrete beam is modeled as a three-diensional solid part. The green composite is modeled as a three-dimensional shell part with four layups. The steel bas and ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo