بایگانی برچسب: abaqus damage simulation

In this tutorial, the Simulation UHPFRC beam with initial void reinforced with CFRP rod and Expoxy under dynamic bending has been investigated. The concrete beam, CFRP rod, epoxy glu are modeled as three-dimensional solid parts. Two rigid body as a hydraulic jacks also are modeled. You can see a figure ...

In this tutorial, the Simulation CEL explosion in the depth of water near the aluminum hull in Abaqus- three sea mine explosion- has been done. The domain is modeled as a three-dimension Eurlerian part. The hull is modeled as a three-dimensional shell part. The water and three TNT parts are ...

In this tutorial, the Simulation air blast explosion over the rebberized concrete column reinforced with green composite in Abaqus has been done. The rubberized concrete column is modeled as a three-dimensional solid part. The green composite with some layers is modeled as a three-dimensional shell part. The steel reinforcements are ...

In this tutorial, the Simulation dynamic bending test of a rubberized concrete beam reinforced with green composite  in abaqus has been investigated. The rubberized concrete beam is modeled as a three-diensional solid part. The green composite is modeled as a three-dimensional shell part with four layups. The steel bas and ...

In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...

In this tutorial the Simulatio bird strike impact with SPH method to the composite blade in Abaqus has been investigated. The bird is modeled as the three-dimension solid part. The composite blade with eight layers is modeled as three-dimensional shell part. You can see a figure of the assembled parts ...

In this tutorial the Simulation CEL explosion inside the CFRP composite vessel in Abaqus has been investigated. The CFRP vessel is modeled as a three-dimensional shell part in sixteen layers with different oreintation. The TNT part is modeled as a three-dimensional solid part. The surounding is modeled as an Eurlerian ...

In this tutorial the Simulation low energy impact on the concrete slab with pre tensioned bars reinforced with GFRP in Abaqus has been studeid. Concrete is modeled as a three-dimensional solid part. The GFRP part is model as plannar shell part. The steel basrs are modeled as three-dimensional wire part ...

In this tutorial the Simulation CFRP water storage tank under close air blast explosion in Abaqus has been investigaed. The CFRP tank is modeled as a three-dimensional shell part. The water is modeled as solid part and it’ll used as reference volume in load section to define the amount and ...

در این ویدئوی آموزشی به شبیه سازی انفجار به روش اویلری در نزدیکی یک مخزن کامپوزیتی حاوی آب در آباکوس و بررسی آسیب مخزن پرداخته ایم. مخزن کامپوزیتی به صورت یک استوانه شل سه بعدی طراحی شده است. هندسه آب به صورت یک جسم سالید سه بعدی و همچنین فضای ...

In this tutorial the Simulation internal explosion of a pipe with steel supporters in Abaqus has been investigated. The steel pipe is modeled as three-dimensional solid part, it can also be shell part. The upper and bottom supports are modeled as three-dimensional solid part. You can see a figure of ...

This tutorial investigates a Simulation air blast explosion test over a reinforced UHPC- Damage analysis. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part. The embedded bars and strips parts are modeled as a three-dimensional wire part. You can see a figure of the assembled parts below The UHPC ...

در این ویدئوی آموزشی به شبیه سازی انفجار در هوا روی یک ستون بتنی فوق توانمند تقویت شده با میلگرد در نرم افزار آباکوس-بررسی تخریب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و تیر بتنی به صورت یک پارت سالید و سه بعدی، میلگردها و خاموت ها به صورت ...

In this tutorial, the Simulation of steel projectile impact to the Reinforced-Ultra-High-Performance Concrete- Damage investigation has been investigated. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part, the embedded beam parts are modeled as a three-dimensional wire part, and finally, the steel projectile is modeled as a solid part. ...

In this package, the high and low-velocity impacts are investigated through 40 step-by-step tutorials for more than 20 hours. Through those 40 separated simulations, all aspects of the impact and collision are studied. Each tutorial contains cae, inp, step-by-step English video, and papers, also some of them have codes. Impact ...

In this tutorial, the Simulation steel bullet impact to the armor panel(Ceramic- Aluminum Foam) in Abaqus has been investigated. The steel bullet is modeled as a three-dimensional solid part. The ceramic and aluminum foam are modeled as three-dimensional solid parts. Because of the symmetry conditions, one-quarter of the whole model ...

در این ویدئوی آموزشی به شبیه سازی برخورد گلوله فولادی به پنل مرکب سرامیک-فوم آلمینیوم در نرم افزار آباکوس پرداخته ایم. هدف از این شبیه سازی بررسی تخریب هدف و گلوله در اثر سرعت بالای برخورد می باشد. گلوله فولادی به صورت سه بعدی و تغییر شکلپذیر، لایه رویی سرامیکی ...

In this tutorial, the Simulation rigid projectile impact to the ceramic-CFRP panel in Abaqus-Damage investigation – has been done. The rigid projectile is modeled as a three-dimensional shell part. The ceramic is modeled as a three-dimensional thick solid part. The CFRP or carbon fiber is modeled as a three-dimensional shell ...

در این ویدئوی آموزشی به شبیه سازی برخورد صلب به یک پنل مرکب سرامیک-CFRP و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل پارت پرتابه صلب به صورت سه بعدی و شل، پارت هدف سرامیکی به صورت یک لایه ضخیم سه بعدی و سالید و در نهایت پارت ...

In this tutorial, the Simulation SPH explosion over the composite panel( Aluminum- Metal Foam) in Abaqus-Damage investigation – has been done. The explosive part, or the TNT is modeled as a three-dimensional solid part. The aluminum sheets are modeled as three-dimensional solid parts. The Aluminum Foam as a core is ...

در این ویدئوی آموزشی به شبیه سازی انفجار به روش SPH روی یک پنل مرکب( آلمینیوم- فوم آلمینیوم) و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی می باشد. پارت ماده منفجره و یا TNT به صورت یک کره توپر و سالید در نظر گرفته ...

In this tutorial, the Simulation rigid impact to the composite panel(CFRP+TPU+AL) in Abaqus-Damage investigation – has been studied. The CFRP part is modeled as a shell part with eight layers. The Thermoplastic polyurethane is modeled as a three-dimensional solid part. The Aluminum part is modeled as a three-dimensional solid part. ...

در این ویدئوی آموزشی به شبیه سازی برخورد جسم صلب به پنل مرکب(CFRP+TPU+AL) و بررسی تخریب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و صفحه کامپوزیتی الیاف کربن به صورت هشت لایه و شل مدل شده است. لایه میانی پلی اورتان یا Thermoplastic polyurethane به ...

In this tutorial, the Simulation RC beam under the repeated impact of the rigid hammer in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The steel rebar and strips are modeled as three-dimensional wire parts. The rigid hammer is modeled as a three-dimensional rigid ...

در این ویدئوی آموزشی به شبیه سازی برخورد تکراری یک جسم صلب به تیر بتنی مسلح در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و تیر بتنی به صورت سالید، میلگرد و خاموت ها به صورت وایر، و جسم صلب به صورت شل و ریجید طراحی ...

In this tutorial, the Simulation Blast response of aluminum/thermoplastic polyurethane sandwich panels in Abaqus has been investigated. The aluminum sheets are modeled as three-dimensional solid parts. The TPU is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below. History presents evidence of the ...

In this tutorial, the Numerical analysis of tilted angle shear connectors in steel-concrete composite systems in Abaqus has been investigated. The concrete block is modeled as a three-dimensional solid part. The steel beam and steel angle connector are modeled as three-dimensional solid parts. Two rigid bodies are used as boundary ...

In this tutorial, the Simulation compression test of the concrete column with and without steel reinforcement-Compression test- has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts and two rigid bodies as boundary zone and hydraulic jack. You can ...

در این ویدئوی آموزشی به شبیه سازی تست فشار ستون کوتاه بتنی با و بدون تقویت کننده فلزی در آباکوس-مقایسه باربری- پرادخته ایم. مدلسازی به صورت سه بعدی شامل هندسه ستون بتنی، میلگرد ها و اجسام صلب در نقش تکیه گاه و جسم وارد کننده نیرو می باشد. ستون بتنی ...

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

In this tutorial, the damage and failure investigation of the CFRP composite military helmet under close blast explosion has been studied. The military helmet is a 3D shell part with eight different layers. The helmet part is imported to the Abaqus because of the part complexity. You can see a ...

In this tutorial, the Seismic behavior of RC exterior wide beam-column joints in Abaqus has been simulated. The concrete beam and column are modeled as three-dimensional solid parts. The steel bars and strips are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Reinforced ...

In this tutorial, the High-velocity impact of a bullet on the RC panel- Paper validation- is investigated. The dimensions are extracted from the paper. The concrete slab is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. The bullet is modeled as a discrete ...

In this course, you will learn all aspects of steel structure modeling and simulation in Abaqus. The lecture contains sixteen sections, in each section, the tutor has explained all thing from A to Z. Geomert modeling, material definition and equations, steps, interaction, load, mesh, and results. The dynamic bolt failure, ...

In this lecture, the High and Low-velocity impact phenomenon is investigated. The lecture duration is more than ten hours and during that, twenty different models are simulated based on the research paper as a reference for the material. We define the proper material model for each part for instance in ...

In this lecture through Twenty step by step tutorial, many aspects of the concrete structure like a beam, RC beam and column, normal concrete, UHPC, and UHPFRC concrete, composite beam, and column, cyclic loading over the RC beam and column, CFDST and CFST column, ECC beam-column joint, high strength concrete ...

In this tutorial, the Simulation cyclic loading of a composite Column(UHPC + Steel box) in Abaqus has been studied. The Ultra-High-Performance Concrete column is modeled as a three-dimensional solid part. The steel box cover is modeled as a three-dimensional shell part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation oblique high-velocity impact of an aluminum rod to the silicon-carbide target in Abaqus has been investigated. The silicon-carbide target is modeled as a three-dimensional solid part. The aluminum projectile is modeled as a three-dimensional solid part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation cyclic loading behavior of a reinforced rubberized concrete column in Abaqus has been investigated. The rubberized concrete column is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation of low energy impact on the RC beam and residual displacement investigation in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire parts. The hammer is modeled as a rigid ...

In this tutorial, the Simulation of rigid body impact on the interior voided RC slab in Abaqus has been investigated. The RC voided slab is modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire parts. The rigid impactor is modeled as a three-dimensional shell part. ...

در این ویدئوی آموزشی به شبیه سازی برخورد جسم صلب به پنل بتنی حفره دار در نرم افزار آباکوس- بررسی تخریب- پرداخته ایم. مدلسازی شامل دال بتنی به صورت سه بعدی و تغییر شکلپذیر، میلگردها به صورت سه بعدی و سیمی و در نهایت جسم صلب به صورت سه بعدی ...

In this tutorial, the Simulation dynamic bending of RC beams strengthened with CFRP rods and Epoxy glue in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The CFRP rod and epoxy glue are modeled as three-dimensional solid parts. The steel bars and strips are ...

In this tutorial, the Simulation blast explosion over the composite panel(Steel-Aluminum-Ceramic-CFRP) in Abaqus has been investigated. The steel and aluminum plates are modeled as three-dimensional solid part. The silicon carbide or ceramic is modeled as a three-dimensional solid part. The CFRP is modeled as a three-dimensional solid part with four ...

In this tutorial, the Simulation dynamic bending test of an interior voided RC UHPC beam in Abaqus has been studied. The Ultra-High-Performance Concrete beam is modeled as three-dimensional solid part with interior sphere voids. The steel bar and strips are modeled as three-dimensional wire parts. The rigid bodies are used ...

In this tutorial, the Simulation ship moving through Ice-Water path in Abaqus by using SPH method has been done. The ship is imported to the Abaqus because of its complex geometry. The ice and water are modeled as a three-dimensional solid part. You can see a figure of the assembled ...

In this tutorial, the Simulation air blast load over a composite beam( UHPFRC- Steel beam with Shear stud) in Abaqus has been investigated. The Ultra-High-Performance-Fiber-Reinforced Concrete is modeled as a three-dimensional solid part. The stud is modeled as a three-dimensional solid part. The steel beam is modeled as a three-dimensional ...

In this tutorial, the Simulation air blast explosion over campsite slab(UHPC-Steel) by using cohesive interaction in Abaqus  has been done. The two steel covers are modeled as three-dimensional solid part. The Ultra-High-Performance concrete is modeled as a three-dimensional solid par. You can see a figure of the assembled parts below ...

In this tutorial, the Simulation low velocity impact on the CFRP-AL Foam-CFRP panel in Abaqus has been investigated. The CFRP are modeled as three-dimensional solid parts with four different fiber direction. The Aluminum-Foam as a core part is modeled as a three-dimensional solid part. The projectile is modeled as the ...

In this tutorial, the Simulation bending test of a steel-concrete(foamed concrete) composite beam in Abaqus  has been studied. The foamed concrete ( containing partial cement replacement) is modeled as a three-dimensional solid part. The steel beam is modeled as a three-dimensional shell part. The steel reinforcement is modeled as a ...