در این ویدئو به شبیه سازی ستون بتنی تقویت شده با میلگرد و CFRP تحت بار عمودی در نرم افزار آباکوس پرداخته ایم.ستون بتنی به صورت پارت سه بعدی تغییر شکلپذیر،میلگردهای دایروی و طولی به صورت پارت وایر سه بعدی، صفحه کربنی دولایه به صورت شل سه بعدی و در ...
ادامه نوشته »
In this tutorial dynamic simulation of tensile test of a steel piece under axial deformation in Abaqus has been investigated. A three dimensional part like below figure is used to model steel geometry To model failure behavior of the steel piece shear and ductile damage with evolution, isotropic plasticity with ...
ادامه نوشته »
In this tutorial Numerical Simulation on Fracturing of Rock under Blast Using Coupled Finite Element Method and Smoothed P article Hydrodynamics has been investigated.Nowadays, drill and blast are still a common excavation technique for rock foundations and underground caverns in the fields of hydro power, transportation and mining because these ...
ادامه نوشته »
در این ویدئو به شبیه سازی قدم به قدم انفجار به روش SPH در میان یک توده سنگ گرانیتی در آباکوس- بررسی آسیب- پرداخته ایم.سنگ و تی ان تی به صورت پارت های سه بعدی تغییر شکلپذیر ترسیم شده اند. در شکل زیر می توانید نمایی از قرار گیری اجزا ...
ادامه نوشته »
In this tutorial Numerical simulation modeling of high velocity impact applied to reinforced concrete panel has been investigated. It is well known that concrete is much stronger in terms of compression than in tension. Because of its high com-pressive strength, and to enhance its tensile strength, tensile reinforcements are added ...
ادامه نوشته »
در این ویدئو به شبیه سازی برخورد گلوله سرعت بالا به یک پنل بتنی تقویت شده در نرم افزار آباکوس-بررسی پارامتر تخریب- پرداخته ایم.در این تحلیل بتن به صورت پارت سه بعدی تغییر شکلپذیر،گلوله به صورت پارت سه بعدی صلب و میلگردها به صورت المان وایر سه بعدی در نظر ...
ادامه نوشته »
In this tutorial Simulation on shock response of marine sandwich structures subjected to UNDEX loading in Abaqus has been investigated.In modern sea combat, in which strike power has increased markedly, the structures of naval ships must be designed to with-stand shock loads resulting from weapon hits.To improve the design of ...
ادامه نوشته »
در این ویدئو به شبیه سازی مرحله به مرحله انفجار زیر آب در فاصله نزدیک روی یک سازه ساندویچی فولادی در نرم افزار آباکوس به روش UNDEX پرداخته ایم. مدلسازی به صورت سه بعدی بوده و هندسه پنل ساندویچی از دو ورق رویی و زیرین به همراه هندسه مشبک ذاخلی ...
ادامه نوشته »
In this tutorial Simulation of hollow steel piles subjected to buried blast loading(CEL explosion) in Abaqus has done.A pile is a load bearing component of a structure that transfers the structural load to the hard soil or rock underground. The modern human civilization and smart infrastructure depend largely on the ...
ادامه نوشته »
در این ویدئو به شبیه سازی قدم به قدم انفجار به روش کوپل اویلری لاگرانژی در عمق خاک روی شمع فلزی در نرم افزار آباکوس پرداخته ایم.شبیه سازی به صورت سه بعدی بوده و شمع های فلزی به صورت لوله و با المان سالید،خاک و ماده منفجره به صورت اویلری ...
ادامه نوشته »
In this tutorial simulation granite stone cutting by using a rigid cutter in Abaqus has been investigated.The granite stone is modeled as three dimensional part ,the cutter and supporter are modeled as rigid body.The Abaqus CAE contains some material model for brittle materials,but they are suitable to simulate the large ...
ادامه نوشته »
در این ویدئو به شبیه سازی مرحله به مرحله برش سنگ با استفاده از یک کاتر صلب در نرم افزار آباکوس پرداخته ایم. کاتر به صورت جسم سه بعدی صلب و سنگ نیز به صورت پارت تغییر شکلپذیر سه بعدی بوده که در زیر آن یک صفحه صلب به عنوان ...
ادامه نوشته »
In this tutorial simulation CFRP jacketed reinforced concrete beam-column joints in Abaqus has been investigated.Various types of strengthening materials such as steel plates, ferrocement, and fiber reinforced polymers are available in the construction industry to be used for jacketing of the affected components, the most common being steel jackets.These types ...
ادامه نوشته »
در این ویدئو به شبیه سازی مرحله به مرحله اتصال تیر به ستون بتنی تقویت شده با میلگرد و CFRP در نرم افزار آباکوس پرداخته ایم. تیر و ستون بتنی به صورت سه بعدی و تغییر شکلپذیر با متریال مدل CDP، میلگردها به صورت پارت وایر و با متریال استیل ...
ادامه نوشته »
در این ویدئو به صحت سنجی و شبیه سازی قدم به قدم فرآیند الکتروهیدرولیک با استفاده از مدل فشار زمان در نرم افزار آباکوس پرداخته ایم. مقاله مورد استفاده در این شبیه سازی در سال ۲۰۱۴ در یکی از ژورنال های الزویر چاپ شده است.شکل‌دهی الکتروهیدرولیکی یک فرایند شکل‌دهی ورق ...
ادامه نوشته »
In this tutorial Simulation concrete slab cutting by using a rigid cutter in Abaqus has been investigated.Concrete cutting is a process of controlled sawing, drilling and removal of concrete performed by skilled operators using special saws that use diamond impregnated blades. Unlike the old-fashioned dusty jack hammer method, modern concrete ...
ادامه نوشته »
In this tutorial simulation concrete beam-column joints in Abaqus has been studied. Strengthening of existing reinforced concrete structures is now a major part of the construction activity all over the world. The RCC structures constructed across the world are often found to exhibit distress and suffer damage, even before service ...
ادامه نوشته »
In this tutorial Simulation steel beam damage under cyclic loading in Abaqus standard has been investigated.Under cyclic loading conditions such as those introduced by earthquake ground motions, the local buckling is initiated in the compression flange. However, it disappears and reappears in subsequent cycles. The beam is modeled as three ...
ادامه نوشته »
In this tutorial Simulation of p-section concrete beams under contact explosion(CEL) conditions in Abaqus has been studied. Reinforced concrete bridges are the most common type of bridges and have a simple structure, low cost and long durability. Among these bridges, reinforced concrete bridges composed of p-section bridge components are among the ...
ادامه نوشته »
In this tutorial numerical simulation of CEL explosion over metal tube in the depth of water in Abaqus has been investigated.An underwater explosion can be divided into two stages: the shock wave and the bubble pulse. Although both inflict severe damage to the adjacent structure, their damage mechanisms are different. Generally, the ...
ادامه نوشته »
In this tutorial Prediction model of depth of penetration for alumina ceramics under garnet impact in Abaqus has been studied .The target and projectile were modeled as three dimensional parts .The JH-2 constitutive model was proposed to describe the response of ceramic materials to large strain rate. The JH-2 constitutive model ...
ادامه نوشته »
In this video Simulation steel drilling process in Abaqus has been investigated.Drilling process is one of the most required machining techniques that accounts for more than 40 % of the total material removal processes and especially has a high frequency of use in aerospace industries . It is significant to ...
ادامه نوشته »
Progressive collapse refers to the failure of one or a group of key structure load-carrying members that gives rise to a more widespread failure of the surrounding members and partial or complete structure collapse. It is defined as the spread of an initial local failure from element to element resulting ...
ادامه نوشته »
With the growing use of composites in military, air vehicles and naval structures, sporting goods and the power industry, the comprehension of impact mechanism and dynamic behavior is critical to composite designers and end users. A wealth of knowledge has been published on dynamic impact response of composite materials and ...
ادامه نوشته »
Insulated concrete sandwich panels are comprised of two outer concrete wythes and an inner layer of foam insulation. They have been increasingly used because of their advantages of light weight and energy efficiency. Various shear connectors can be used to connect the two outer concrete wythes. More recently, Fiber-Reinforced Polymer ...
ادامه نوشته »
Explosions, whether accidental or planned, can cause significant damage to the built infrastructure and result in fatalities to occupants of buildings in close proximity to the center of explosion. The increase in the number of terrorist attacks over the past few decades has led to growing concerns about the performance ...
ادامه نوشته »
Honeycomb sandwich structures are broadly used in the aerospace and automotive industries, particularly as energy-absorption materials, and there are limited applications in civil infrastructure, such as highway bridges and building construction. Due to their unique and advantageous properties such as high mechanical performance per unit weight and high energy-absorption capability, ...
ادامه نوشته »
In this video you can see Simulation blast loading over concrete slab reinforced by composite layers in Abaqus step by step.With the increased world tension, terrorist bombing attacks or accidental explosions are becoming a large threat to infra-structure such as the important economic, military and civilian facilities. The research on ...
ادامه نوشته »
Abaqus tutorials Abaqus tutorials