بایگانی برچسب: Abaqus CFRP reinforcement

Simulation air blast explosion over a composite panel(CFRP-Ceramic-GFPP) in Abaqus has been investigated in this tutorial. The CFRP and Glass fiber Polypropylene are modeled as shell parts with some layers. The ceramic core is modeled as a solid part. You can see a figure of the assembled parts below The ...

In this tutorial, the Simulation air blast explosion over a composite panel(Silica glass-Aluminum-CFRP) in Abaqus has been investigated. The silica glass is modeled as a three-dimensional part. The aluminum as the middle layer is modeled as a three-dimensional solid part. The CFRP as the backplate is modeled as a shell ...

In this tutorial, the Simulation of a steel bullet impact on the composite panel (Boron carbide-CFRP-Gelatin) in Abaqus has been investigated. The bullet is modeled as a three-dimensional solid part. The boron carbide and gelatin are modeled as three-dimensional solid parts. The CFRP is modeled as a shell with eight ...

In this tutorial the Simulation CFRP water storage tank under close air blast explosion in Abaqus has been investigaed. The CFRP tank is modeled as a three-dimensional shell part. The water is modeled as solid part and it’ll used as reference volume in load section to define the amount and ...

In this tutorial, the Simulation rigid impact to the composite panel(CFRP+TPU+AL) in Abaqus-Damage investigation – has been studied. The CFRP part is modeled as a shell part with eight layers. The Thermoplastic polyurethane is modeled as a three-dimensional solid part. The Aluminum part is modeled as a three-dimensional solid part. ...

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

In this tutorial, the damage and failure investigation of the CFRP composite military helmet under close blast explosion has been studied. The military helmet is a 3D shell part with eight different layers. The helmet part is imported to the Abaqus because of the part complexity. You can see a ...

In this tutorial, the Simulation blast explosion over the composite panel(Steel-Aluminum-Ceramic-CFRP) in Abaqus has been investigated. The steel and aluminum plates are modeled as three-dimensional solid part. The silicon carbide or ceramic is modeled as a three-dimensional solid part. The CFRP is modeled as a three-dimensional solid part with four ...

In this tutorial, the Simulation low velocity impact on the CFRP-AL Foam-CFRP panel in Abaqus has been investigated. The CFRP are modeled as three-dimensional solid parts with four different fiber direction. The Aluminum-Foam as a core part is modeled as a three-dimensional solid part. The projectile is modeled as the ...

In this tutorial, the Simulation rigid ball impact on the steel pipe with and without the CFRP reinfocement layers in Abaqus  has been investigated. The steel pipe is modeled as a three-dimensional shell part. The CFRP pipe is modeled as three-dimensional shell part and conventional shell section with eight layers ...

In this tutorial, the Simulation three point bending of a RC beam reinforced with CFRP in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire parts. The CFRP sheet is modeled as a three-dimensional shell ...

In this tutorial, the Simulation compression test of the UHPFRC column with internal CFRP box in Abaqus has been investigated. The Ultra-High-Performance-Fiber-Reinforced concrete is modeled as a three-dimensional solid part. The CFRP internal box is modeled as a three-dimensional shell part. Two rigid bodies are used as supporter and body ...

In this tutorial, the Simulation static bending of the UHPC beam with CFRP pipe core in Abaqus has been investigated. The concrete beam is modeled as three-dimensional solid part. The CFRP pipe core is modeled as a three-dimensional shell part. The rigid body part is used as a force body.You ...

In this tutorial, the Simulation of hollow core square reinforced concrete columns wrapped with CFRP under compression in Abaqus has been studied. The concrete part is modeled as a three-dimensional solid part. The CFRP box in modeled as a three-dimensional shell part. The steel bars and strips are modeled as ...

In this tutorial, the Simulation four point bending of the CFRP sheet with six layers (inter laminar cohesive behavior) in Abaqus has been studied. The CFRP layers are modeled as three-dimensional solid part. Two rigid bodies were used as hydraulic jack to apply the load. You can see a figure ...

In this tutorial, the Simulation four-point bending of the UHPC slab reinforced with steel bars and the GFRP sheet in Abaqus has been investigated. The UHP concrete slab is modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire parts. The GFRP sheet with eight layers ...

In this tutorial, the Simulation sequential air blast explosion over the concrete slab reinforced with CFRP sheet in Abaqus has been studied. The concrete slab is modeled as a three-dimensional solid part. The CFRP sheet is modeled as a three-dimensional shell part. You can see figures of the assembled parts ...

In this tutorial, the Simulation axial compression of the damaged concrete column with initial residual stress reinforced with CFRP in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The CFRP box is modeled as a three-dimensional shell part. In the first simulation of the ...

In this tutorial, the Simulation damaged concrete beam with initial residual stress reinforced with CFRP sheet under bending load in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The CFRP sheet is model as a three-dimensional shell part. In this tutorial, at the first ...

In this tutorial, the simulation four points bending of an RC beam strengthened with CFRP sheet in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The strips and bars are modeled as three-dimensional wire part. The CFRP sheet is modeled as a three-dimensional shell ...

In this tutorial, Simulation cyclic loading over the steel beam-column structure reinforced with CFRP in Abaqus has been investigated. The steel beam and column are modeled as a three-dimensional shell part. The CFRP plates are modeled as a planar shell part. You can see a figure of the assembled parts ...

In this tutorial Simulation steel pipe reinforcement with CFRP layouts in Abaqus under three points bending has been studied. Circular hollow section (CHS) are widely used in many applications but predominantly used as pipelines in the oil and gas industry. Natural resources like oil and gas constitute the major share ...

In this tutorial Finite element modeling of reinforced concrete beams externally strengthened in flexure with side-bonded CFRP laminates in Abaqus has been done. The concrete beam and epoxy glue are modeled as three dimensional part,the CFRP is modeled as three dimensional shell part,the bar is modeled as three dimensional wire ...