Introduction to Brittle Damage Modeling in Abaqus: Johnson-Holmquist and Beissel Models Brittle damage refers to the failure mechanism observed in brittle materials such as concrete, glass, ice, and ceramics. Unlike ductile materials, which undergo significant plastic deformation before failure, brittle materials typically fail suddenly with little to no warning and ...

Introduction to Tunnel and TBM Simulation in Abaqus Abaqus is a powerful finite element analysis (FEA) software widely used in engineering and scientific research. It is particularly effective for simulating complex geotechnical problems, including tunnel construction and Tunnel Boring Machine (TBM) operations. Simulating tunnels and TBMs in Abaqus allows engineers ...

Fatigue and Cyclic Loading in Abaqus Mechanical fatigue is a phenomenon where a material undergoes progressive and localized structural damage when subjected to cyclic or fluctuating stresses, even if these stresses are below the material’s ultimate tensile strength. Over time, this repeated loading and unloading can lead to the initiation ...

Ultra-High-Performance Fiber-Reinforced Concrete (UHPFRC) in Abaqus Ultra-high-performance fiber-reinforced Concrete (UHPFRC) is an advanced construction material characterized by its exceptional mechanical properties, including high compressive strength, tensile strength, and durability. UHPFRC is typically composed of a dense matrix of fine particles, high-strength cement, and steel or synthetic fibers, which enhance its ...

Introduction to Ultra-High-Performance Concrete (UHPC) in Abaqus Ultra-high-performance concrete (UHPC) is an advanced cementitious material characterized by its exceptional strength, durability, and ductility. It typically has a compressive strength exceeding 150 MPa and can reach up to 250 MPa or higher, along with superior tensile strength and resistance to environmental ...

Introduction to Masonry Wall and Structure Simulation in Abaqus Masonry walls are structural elements made from individual units (such as bricks, stones, or concrete blocks) bound together by mortar. They are widely used in construction due to their durability, thermal insulation, and aesthetic appeal. However, simulating masonry structures can be ...

Introduction to Polymeric and Metal Foam Simulation in Abaqus Polymeric and metal foam are advanced materials widely used in industries such as aerospace, automotive, biomedical, and construction due to their unique properties, including high strength-to-weight ratios, energy absorption, and thermal and acoustic insulation. Simulating these materials in Abaqus, a powerful ...

Introduction to Earthquake and Seismic Analysis in Abaqus Earthquake and seismic analysis are critical aspects of structural engineering, aimed at understanding and mitigating the effects of seismic events on structures. Abaqus, a powerful finite element analysis (FEA) software developed by Dassault Systèmes, is widely used for simulating and analyzing the ...

Introduction to Bolt Analysis in Abaqus Abaqus is a powerful finite element analysis (FEA) software widely used for simulating complex mechanical systems, including bolted joints. Bolt analysis in Abaqus involves modeling the bolt, applying preload, and simulating the behavior of the bolted joint under various loading conditions. This analysis helps ...

Introduction to Dam Simulation and Analysis in Abaqus Abaqus is a powerful finite element analysis (FEA) software widely used in engineering and scientific research for simulating complex physical behaviors. When it comes to dam simulation and analysis, Abaqus provides a comprehensive suite of tools to model, analyze, and predict the performance of ...

Introduction to Rock and Stone Simulation and Analysis in Abaqus Rock and stone analysis in Abaqus software involves simulating the mechanical behavior of geological materials, such as rocks, stones, and other geomaterials, under various loading and environmental conditions. Abaqus, a powerful finite element analysis (FEA) software, is widely used in ...

Introduction to Cold Spray Process The cold spray process is an advanced additive manufacturing and coating technology that involves the deposition of solid powder particles onto a substrate at high velocities but relatively low temperatures. Unlike traditional thermal spray methods, which often involve melting or significant heating of the feedstock material, ...

Introduction to Wood Simulation and Analysis in Abaqus Wood is a complex, anisotropic material with unique mechanical properties that vary depending on grain orientation, moisture content, and other factors. Simulating and analyzing wood behavior in engineering applications requires specialized tools and methodologies. Abaqus, a powerful finite element analysis (FEA) software, ...

Introduction to Pull-Test Simulation in Abaqus Pull-test simulation in Abaqus is a computational method used to analyze the mechanical behavior of materials and structures under tensile loading. This type of simulation is commonly employed in various industries, including aerospace, automotive, and civil engineering, to predict the performance and failure mechanisms ...

Introduction to Glass Simulation and Analysis in Abaqus Abaqus, a powerful finite element analysis (FEA) software developed by Dassault Systèmes, is widely used for simulating and analyzing complex mechanical behaviors in various materials, including glass. Glass, being a brittle material with unique properties such as transparency, hardness, and low ductility, ...

Introduction to Ice Simulation in Abaqus Abaqus, a powerful finite element analysis (FEA) software developed by Dassault Systèmes, is widely used to simulate complex mechanical behaviors in various materials and structures. One of its advanced applications is simulating ice and its interaction with structures, which is particularly important in industries ...

Fire simulation in Abaqus is a powerful tool for analyzing the effects of fire and thermal loads on structures and materials. Abaqus, a widely used finite element analysis (FEA) software, provides advanced capabilities to model heat transfer, thermal-structural coupling, and material degradation under high-temperature conditions. This makes it suitable for ...

In this tutorial, the Simulation of composite panels made of profiled steel skins and concrete under axial compressive load in Abaqus has been studied. The steel profile is modeled as a three-dimensional shell part. The concrete core is modeled as a three-dimensional solid part. You can see a figure of ...

در این ویدئوی آموزشی به شبیه سازی تست فشار استاتیکی و دینامیکی پروفایل فولادی پر شده با بتن در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه پروفیل فولادی به صورت شل و سه بعدی و هندسه بتن به صورت سالید و سه بعدی می باشد. در شکل زیر نحوه ...

In this tutorial, the Simulation air blast load over CFRP facings and PET foam core panel in Abaqus has been investigated. The CFRP sheets are modeled as three-dimensional parts with sixteen layers, and the Polyethylene terephthalate(PET) foam is modeled as a three-dimensional solid part. You can see a figure of ...

در این ویدئوی آموزشی به شبیه سازی انفجار در نزدیکی پنل مرکب(CFRP+PET foam+CFRP) در نرم افزار آباکوس پرداخته ایم. مدلسازی تقارنی بوده و فقط یک چهارم هندسه کل به منظور کاهش محاسبات در نظر گرفته شده است. در شکل زیر میتوانید نحوه قرارگیری ورق های کامپوزیت CFRP و فوم PET ...

In this tutorial, the Simulation durability of GFRP-SFRSC concrete adhesively bonded connection in Abaqus has been done. The GFRP beam and the steel fiber-reinforced self-compacting concrete (SFRSCC) are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below Fiber-reinforced polymer (FRP) materials are becoming increasingly considered ...

در این ویدئوی آموزشی به شبیه سازی اتصال تیر GFRP به بتن SFRSCC تحت بار کششی در نرم افزار آباکوس پرداخته ایم. مجموعه شامل هندسه تیر کامپوزیتی GFRP و دال بتنی از نوع بتن SFRSCC به صورت سالید و سه بعدی می باشد. با توجه به تقارن موجود در مساله ...

In this tutorial, the Simulation Wood-Cement wall under seismic loading in Abaqus has been investigated. The wood-cement wall is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts below Bio-sourced materials combined with a cementitious matrix ...

در این ویدئوی آموزشی به شبیه سازی بارگذاری چرخه ای دیوار کامپوزیت چوب-سیمان در نرم افزار آباکوس پرداخته ایم. دیوار چوب-سیمانی به صورت سه بعدی و تغییر شکل پذیر طراحی شده است. میلگردهای داخلی نیز به صورت سیمی در داخل دیوار قرار گرفته اند. در شکل زیر می توانید نحوه ...

In this tutorial, the Simulation RC slab with PET foam core under a four-point bending test in Abaqus has been investigated. The concrete and PET foam are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts below ...

در این ویدئوی آموزشی به شبیه سازی خمش چهار محوره دال بتنی تقویت شده با میلگرد و فوم PET در نرم افزار آباکوس پردخته ایم. مدلسازی شامل هندسه بتن و فوم به صورت سالید و سه بعدی، هندسه میلگردهای تقویت کننده به صورت سیمی، و در نهایت اجزای صلب به ...

This tutorial investigates the Simulation of the dynamic behavior of T-shaped steel-reinforced concrete columns under high and low-impact loading in Abaqus. The concrete and steel T-shaped columns are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see figures of the assembled parts below ...

در این ویدئوی آموزشی به شبیه سازی برخورد سرعت بالا و پایین به تیر بتنی تقویت شده با میلگرد و هسته تیر فولادی T شکل در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل تیر بتنی به صورت سالید، تیر فولادی T شکل به صورت سالید، میلگردها به صورت سیمی و ...

In this tutorial, the ُSimulation of the behavior of bolted shear connectors in composite slabs with steel deck in Abaqus has been studied. The steel beam, concrete, and bolts are modeled as a three-dimensional solid part. The steel deck is modeled as a shell part. You can see a figure ...

در این ویدئوی آموزشی به شبیه سازی اتصال دهنده برشی در سیستم دال بتنی-عرشه فولادی در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه بتن به صورت سه بعدی، پیچ ها به صورت سه بعدی، تیرو فولادی به صورت سالید، و در نهایت هندسه عرشه به صورت شل می باشد. ...

In this tutorial, the Shear-bending failure modeling of concrete ribbed slabs strengthened with UHPFRC in Abaqus has been investigated. The slab has three sections, untracked concrete, cracked concrete, and UHPFRC. All three parts are modeled as three-dimensional solid parts. the steel reinforcements are modeled as wire parts. You can see ...

در این ویدئوی آموزشی به شبیه سازی خمش دال بتنی مرکب(بتن سالم، بتن ترک خورده، بتن الیافی) در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه دال بتنی سالم، دال بتنی ترک خورده و دال بتنی الیافی می باشد. میلگردها نیر به صورت سیمی و سه بعدی مدل شده اند. ...

In this tutorial, the Simulation composite Pipe(Aluminum-Bamboo fiber-Aluminum) under internal blast in Abaqus has been investigated. All three pipes are modeled as shell parts. You can see a figure of the assembled parts below The configuration of a composite pipe, which combines the advantages of joining two thin, stiff, and ...

در این ویدئوی آموزشی به شبیه سازی انفجار داخلی در یک لوله کامپوزیتی(آلمینیوم_الیاف بامبو-آلمینیوم) در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه لوله آلمینیومی داخلی، لوله کامپوزیتی از جنس الیاف بامبو در میانه، و در نهایت هندسه لوله آلمینیومی خارجی می باشد. در شکل زیر نحوه قرارگیری اجزا در ...

In this tutorial, the finite element analysis on the seismic behavior of CFRP-strengthened seismic-composite steel-concrete frame column in Abaqus has been investigated. The concrete and steel columns are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. The CFRP box is modeled as a shell part. ...

در این ویدئوی آموزشی به شبیه سازی بارگذاری سیکلی ستون بتنی تقویت شده با میلگرد، هسته تیر فولادی و CFRP در پایه در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل ستون بتنی و هسته فولادی به صورت تیر I شکل سالید، میلگردها تقویت کننده به صورت سیمی، و در نهایت ...

This tutorial investigates the Simulation behavior of a new type of reinforced concrete composite slab with a joint in Abaqus. The precast plank concrete and in-situ concrete topping are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled ...

در این ویدئوی آموزشی به شبیه سازی دال بتنی با اتصال جدید در میانه تحت اثر بار خمشی در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه دال سه تکه که تکه میانی از بتن مقاوم تری تهیه شده است. تمامی اجزای بتنی به صورت سه بعدی و سالید ترسیم ...

In this tutorial, the Simulation of the Kalthoff–Winkler experiment crack growth using a peridynamic model under low-velocity impact in Abaqus has been investigated. Both two- and three-dimensional models can be used to model the plate. Fracture and failure analysis has always been one of the major concerns in theoretical studies ...

In this tutorial, the crushing analysis of a foam-filled aluminum/CFRP hybrid tube against transverse impact in Abaqus was done. The aluminum tube, CFRP, and aluminum foam are modeled as three-dimensional parts. You can see a figure of the assembled parts below Thin-walled structures made of conventional metals, such as aluminum ...

در این ویدئوی آموزشی به شبیه سازی تست کراش لوله آلمینیومی تقویت شده با CFRP و پر شده با فوم آلمینیوم در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه لوله آلمینیومی خارجی، لوله CFRP میانی، هندسه فوم آلمینیومی داخلی و در نهایت اجسام صلب می باشد. در شکل زیر ...

In this tutorial, the Simulation of shear stud distribution on load capacity of the steel-concrete composite beam in Abaqus has been investigated. The concrete slab, steel beam, and studs are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the ...

در این ویدئوی آموزشی به شبیه سازی خمش استاتیکی دال کامپوزیتی( بتن+تیر فولادی با گلمیخ) در نرم افزار آباکوس پرداخته ایم. دال بتنی به صورت سالید و سه بعدی، میلگردهای تقویت کننده بتن به صورت سیمی، تیر فولادی به صورت سالید و سه بعدی، گلمیخ ها نیز به صورت سالید ...

In this tutorial, the Fire analysis of a Steel-Timber composite beam in Abaqus has been done. Both steel and timber wood beams are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below The combination of timber and steel in a single-beam cross-section can result ...

در این ویدئوی آموزشی به شبیه سازی فرآیند آتش سوزی روی یک تیر چوبی با هسته فولادی در نرم افزار آباکوس در نرم افزار آبکاوس پرداخته ایم. در این مثال با توجه به ماهیت آتش سوزی نیاز به طراحی اجزا به صورت سالید و سه بعدی می باشد. در شکل ...

In this tutorial, the Numerical investigation on damage characteristics of ice sheet subjected to underwater explosion load in Abaqus has been studied. The ice is modeled as a three-dimensional solid part. The air, soil, water, and TNT are modeled as an Eulerian part. You can see a figure of the ...

در این ویدئوی آموزشی به شبیه سازی انفجار زیر آب در نزدیکی لایه یخ به روش کوپل اویلری لاگرانژی در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه یخ به صورت سالید، هندسه های خاک، آب، ماده منفجره و هوا به صورت اویلری و سه بعدی می باشد. با توجه ...

In this tutorial, the Flexural response and load capacity of reinforced concrete beam strengthened with reinforced mortar layer in Abaqus has been studied. The concrete and mortar are modeled as three-dimensional solid parts. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts ...

در این ویدئوی آموزشی به شبیه سازی خمش چهار محوره تیر بتنی تقویت شده با لایه سیمانی در نرم افزار آباکوس پرداخته ایم. مدلسازی خمش شامل تیر بتنی سه بعدی، میلگرد و خاموت های تقویت کننده، لایه مقاوم کننده سیمانی به همراه میلگردهای داخلی می باشد. در شکل زیر نحوه ...